63310A 1 Mercury TILT STOP LEVER


63310A 1 TILT STOP LEVER Mercury 1007208, 1010208, 1020208, 1040100, 1040102, 1045205, 1075202, 1075204, 1110102, 1110204, 1200203 TILT
63310A 1 TILT STOP LEVER Mercury
Rating:
8

Buy TILT STOP LEVER 63310A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Mercury entire parts catalog list:

1007208 1978
1010208 1978
1020208 1978,1979,1980
1040100 1970
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075202 1972,1973
1075204 1974,1975,1976,1977
1110102 1972,1973
1110204 1974,1975,1976,1977
1200203 1973,1974,1975,1976,1977

Information:

Start By:a. remove flywheel
The crankshaft rear seal and wear sleeve must both be removed because they must be replaced as a new set. The new seal set must not be separated.
1. Use a sharp punch and a hammer to put four equally spaced holes in seal (1).2. Install the tip of Tool (A) into the seal, and use the slide hammer to pull it out of the flywheel housing. Change the location of Tool (A) in the seal in order to pull the seal out evenly. 3. Install two 5/8 "-18 NF × 4 in. (102 mm) long bolts (2) to hold the crankshaft rear gear in position.4. Install 5P-7314 Distorter Ring (3) [part of Tooling (B)] in the space where the seal was removed.
Be careful not to damage the crankshaft rear gear.
5. Use 5P-7312 Distorter Ring (4) [part of Tooling (B)] to distort the wear sleeve. Put the end of the distorter in the space where the seal was removed.6. Turn the distorter to cause distortion to the wear sleeve. Move the distorter to another position, and turn the distorter again. Do this procedure until the wear sleeve is loose on the crankshaft.7. Remove the distorter, distorter ring and wear sleeve.Install Crankshaft Rear Seal & Wear Sleeve
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
1. Fasten Tooling (A) to the crankshaft rear gear.2. Use 6V-1541 Quick Cure Primer to clean the outside diameter of the crankshaft rear gear and inside diameter of the wear sleeve in seal assembly (1).3. Put 9S-3265 Retaining Compound on the outside diameter of the crankshaft rear gear and the inside diameter of the wear sleeve in seal assembly (1).
Do not separate the lip-type seal from the wear sleeve. The material in the large lip of the seal can be damaged easily. A scratch or rub (not visible) from a finger can damage the seal enough that it cannot be used. Install the sleeve in the seal. Once there is separation of the sleeve and lip-type seal they cannot be used again and must be replaced with a new seal group. Do not use any type of lubrication during installation of the seal group. If any type of lubrication is used in the installation of the seal group, early seal failure can result.
4. Put seal group (1) in position on Tooling (A). Be sure direction arrows on the seal are the same as crankshaft rotation. 5. Put clean engine oil on the face of washer on nut (2) [part of Tooling (B)] that contacts the installer.6. Install Tooling (B) onto Tooling (A), and install nut (2) [part of Tooling (B)] on the threaded shaft of Tooling (A). 7. Tighten nut (2) until Tooling (B) contacts Tooling (A).8. Remove Tooling (A) and (B).End By:a. install flywheel


Parts tilt Mercury:

45757
 
45757 TILT TUBE
1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
55952A 1
 
55952A 1 TILT LOCK PIN
1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30685
56373A 1
 
56373A 1 TILT LOCK PIN ASSEMBLY
1020100, 1020202, 1020208, 1200203
74250
 
74250 TILT TUBE, CLAMP TO SWIVEL BRACKET
1007208, 1010208, 1045205, 1075204, 1110204
71418A 2
 
71418A 2 TILT LOCK PIN ASSEMBLY
1005200, 1007208, 1007209, 1010208, 1045205, 1075204, 1110204
Back to top