97296A 1 Mercury TILT PIN ASSEMBLY


97296A 1 TILT PIN ASSEMBLY Mercury 1018200, 1025200 TILT
97296A 1 TILT PIN ASSEMBLY Mercury
Rating:
29

Buy TILT PIN ASSEMBLY 97296A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

1018200   1025200   Mercury

Mercury entire parts catalog list:

1018200 1980,1982,1983
1025200 1980,1982,1983

Information:

Probable Causes
Diagnostic codes and event codes
Engine parameters
Engine software
Electrical connectors
Fuel supply
Cold mode operation and cold cylinder cutout
Throttle signal
Air intake and exhaust system
Cylinder performance
InjectorsRecommended Actions
Diagnostic Codes and Event Codes
Check for active diagnostic codes on Caterpillar Electronic Technician (ET). Troubleshoot any active codes before continuing with this procedure.Engine Parameters
Verify that the current flash file has been installed and then verify that the correct engine parameters are being used.Engine Software
Verify that the correct engine software is installed.Electrical Connectors
Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and any other applicable connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to Operation and Maintenance Manual for more information.
Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Air in the fuel can cause the engine to run rough. Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel.
Check the fuel tank for foreign objects which may block the fuel supply.
Check the fuel transfer pump.
Check the fuel filters.
Check the diesel fuel for contamination. Refer to Systems Operation/Testing and Adjusting.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Cold Mode Operation and Cold Cylinder Cutout
Use Cat ET in order to verify that the engine has exited cold mode. During cold mode, fuel injection timing is modified. When the engine is in cold mode, the cold cylinder cutout strategy may be active. Cold mode cylinder cutouts may cause variations in vibration and available power. This is normal operation.Throttle Signal
Monitor the throttle signal on Cat ET. Verify that the throttle signal is smooth from the low idle position to the high idle position. Refer to Troubleshooting, "Speed Control - Test".Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.Cylinder Performance
Check the valve lash and reset the valve lash, if necessary. Refer to Systems Operation/Testing and Adjusting.Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to determine the performance of each cylinder. Refer to Troubleshooting, "Injector Solenoid - Test" for the proper procedure.


Parts tilt Mercury:

99929A 1
 
99929A 1 TILT PIN ASSEMBLY
1018200, 1018204, 1020201BC, 1025200
85151
 
85151 TILT TUBE
1018200, 1025200
Back to top