26020 WASHER, CRANKCASE TO CYLINDER BLOCK SCREW Mercury
10402139D, 1050312BC, 1060504, 1070500, 1090524, 1115525, 1650502, 1650503, 1650506, 1700507
WASHER
Price: query
Rating:
Compatible models:
Mercury entire parts catalog list:
1050312BC 1988,1989,1990
- CYLINDER BLOCK » 26020
1070500 1980,1982,1983
1090524 1984,1985,1986,1987,1988
1115525 1985
1650502 1972
1650503 1973,1974,1975
1650506 1976
1700507 1977,1978,1979
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 227-4390 E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, piston rings, outer surface of the piston and the bearing shells for the connecting rod. Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g02013213
Install Tooling (B) onto piston (4). Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin. Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g02447296
Install connecting rod cap (2) onto connecting rod (1). Note: Ensure that dot punched number in Position (X) on connecting rod cap (2) matches dot punched number in Position (X) on connecting rod (1). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old bolts in order to secure the connecting rod cap.
Install new bolts (3) to connecting rod (1). Use Tooling (C) in order to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 9 in order to install the remaining pistons and connecting rods. End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.
Parts washer Mercury:
34392
34392 WASHER
1005200, 1020100, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102, 1650502, 1650503
20533
20533 WASHER (40)
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1075524, 1080500, 1080508, 1090520, 1090524, 1110100, 1110102, 1110204, 1115100, 1115520, 1115523, 1115525, 1135100, 1140520, 1150625, 1150628, 1175626, 1200628
49221
49221 WASHER, NEOPRENE - GEAR HOUSING FLUSHING PLUG
1004200, 1020100, 1020202, 1020208, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040206, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302
22753
22753 WASHER, CRANKCASE TO CYLINDER BLOCK SCREW (LOWER)
1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1650503, 1800100, 1850503
70132
70132 WASHER, WATER JACKET COVER FASTENING SCREW
1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1031203PD, 1031203UD, 1035204, 1035207, 10402139D, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1045217, 1050200, 1050302DB, 1050302FB, 1050302
28420
48527
27736
27736 WASHER
1018200, 1025200, 1050312BC, 1075524, 1150625, 1150628, 1200628, 1225620, 1250422GD, 1300623