28008 Mercury WASHER, THROTTLE CONTOL LEVER SCREW


28008 WASHER, THROTTLE CONTOL LEVER SCREW Mercury 1115100, 1135100, 1400100, 1402202, 1402205, 1500100, 1500101, 1500206, 1650100, 1650502, 1650503, 1650506, 1800100 WASHER
28008 WASHER, THROTTLE CONTOL LEVER SCREW Mercury
Rating:
8

Buy WASHER, THROTTLE CONTOL LEVER SCREW 28008 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Mercury entire parts catalog list:

Information:

Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed with the draining cold oil. Drain the crankcase with the engine stopped. Drain the crankcase with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will cause the waste particles to be recirculated through the engine lubrication system with the new oil.Drain the Engine Oil
After the engine has been run at the normal operating temperature, stop the engine. Use one of the following methods to drain the engine crankcase oil:
If the engine is equipped with a drain valve, turn the drain valve knob counterclockwise in order to drain the oil. After the oil has drained, turn the drain valve knob clockwise in order to close the drain valve.
If the engine is not equipped with a drain valve, remove the oil drain plug in order to allow the oil to drain. If the engine is equipped with a shallow sump, remove the bottom oil drain plugs from both ends of the oil pan.After the oil has drained, the oil drain plugs should be cleaned and installed.Replace the Oil Filter
Cat oil filters are built to Caterpillar specifications. Use of an oil filter not recommended by Caterpillar could result in severe engine damage to the engine bearings, crankshaft, etc., as a result of the larger waste particles from unfiltered oil entering the engine lubricating system. Only use oil filters recommended by Caterpillar.
Remove the oil filter with a 1U-8760 Chain Wrench.
Cut the oil filter open with a 175-7546 Oil Filter Cutter Gp. Break apart the pleats and inspect the oil filter for metal debris. An excessive amount of metal debris in the oil filter may indicate early wear or a pending failure. Use a magnet to differentiate between the ferrous metals and the nonferrous metals that are found in the oil filter element. Ferrous metals may indicate wear on the steel and cast iron parts of the engine.Nonferrous metals may indicate wear on the aluminum parts, brass parts, or bronze parts of the engine. Parts that may be affected include the following items: main bearings, rod bearings, turbocharger bearings and cylinder heads.Due to normal wear and friction, it is not uncommon to find small amounts of debris in the oil filter. Consult your Cat dealer in order to arrange for a further analysis if an excessive amount of debris is found in the oil filter.
Illustration 1 g00103713
Typical filter mounting base and filter gasket
Clean the sealing surface of the filter mounting base. Ensure that all of the old oil filter gasket is removed.
Apply clean engine oil to the new oil filter gasket.
Do not fill the oil filters with oil before installing them. This oil would not be filtered and could be contaminated. Contaminated oil can cause accelerated wear to engine components.
Install the oil filter. Tighten the oil filter until the oil filter gasket contacts the base. Tighten the oil filter by hand according to the instructions that are shown on the oil filter. Do not overtighten the oil filter. Fill the Engine Crankcase
Remove the oil filler cap. Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations" or Operation and Maintenance Manual, "Refill Capacities"for more information.
If equipped with an auxiliary oil filter system or a remote oil filter system, follow the OEM or filter manufacturer's recommendations. Under filling or overfilling the crankcase with oil can cause engine damage.
To prevent crankshaft bearing damage, crank the engine with the fuel OFF. This will fill the oil filters before starting the engine. Do not crank the engine for more than 30 seconds.
Start the engine and run the engine at "LOW IDLE" for 2 minutes. Perform this procedure in order to ensure that the lubrication system has oil and that the oil filters are filled. Inspect the oil filter for oil leaks.
Stop the engine and allow the oil to drain back to the sump for a minimum of 10 minutes.
Remove the oil level gauge in order to check the oil level. Maintain the oil level between the "ADD" and "FULL" marks on the oil level gauge.


Parts washer Mercury:

34392
 
34392 WASHER
1005200, 1020100, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102, 1650502, 1650503
35559
 
35559 WASHER (39)(40)
1005200, 1007208, 1007209, 1010208, 1020100, 1020202, 1020208, 1035204, 1035207, 1040100, 1040102, 10402139D, 1045205, 1045217, 1050200, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203, 1500100
59061
 
59061 WASHER, STATOR LEAD TO STOP SWITCH
1020100, 1020202, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203, 1402202, 1402205, 1500101, 1500205
30164
 
30164 WASHER, THROTTLE LONK
1003203, 1003209, 1004200, 1005200, 1007209, 1020100, 1020201BC, 1020202, 1020208, 1040206, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1080508, 1090524, 1090528, 111047JHD, 1115503, 1115525, 1115528, 1135412SD, 1135412VD, 113541
38453
 
38453 WASHER, NYLON - WATER OUTLET TUBE
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1400100, 1402202, 1402205, 1500100, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
55907
 
55907 WASHER, SPLINED - PROPELLER SHAFT
1400100, 1402202, 1500101
Back to top