36076 WASHER, WAVE - TILT STOP LEVER SCREW Mercury
1020100, 1020202
WASHER
Price: query
Rating:
Mercury entire parts catalog list:
1020202 1972
Information:
TRACTOR ENGINE SHOWN1. Remove bolt (1) that holds suction bell (3) to the oil pan plate. Bend the locks away from bolts (2). Remove bolts (2) that hold the suction tube to the oil pump. Remove the gasket from between the suction tube flange and the oil pump.
TRACTOR ENGINE SHOWN2. Remove two bolts (5) that hold scavenge tube manifold (6) to the oil pump. Remove manifold (6) from tube (4). Check O-ring seals on tube (4). Make a replacement of the seals if necessary. Remove bolts (7) and remove the oil pump.Install Oil Pump
TRACTOR ENGINE SHOWN1. Put oil pump (1) in position under the cylinder block and install the bolts that hold it.
TRACTOR ENGINE SHOWN2. Install a new gasket between the oil pump and the scavenge tube manifold. Install manifold on tube. Install manifold on tube. Install bolts (2) that hold manifold to oil pump.3. Put suction tube (3) in position on the oil pump. Make sure there is a new gasket between the flange on the suction tube and the oil pump.4. Install the bolts that hold the suction tube to the oil pump. Bend the locks against the bolts. Install the bolt that holds the bracket on the suction bell to the oil pan plate.end by: a) install oil pan Disassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing as shown. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body assembly as shown.2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings as shown. Install the bearings until they are even with the outside surface of the oil pump body assembly.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATION.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by: a) install oil pump
Parts washer Mercury:
59061
59061 WASHER, STATOR LEAD TO STOP SWITCH
1020100, 1020202, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203, 1402202, 1402205, 1500101, 1500205
20260
20260 WASHER, SEALING - FLUSH SCREW
1003203, 1003209, 1004200, 1005200, 1007208, 1007209, 1010208, 1018200, 1018204, 1020100, 1020202, 1020208, 1025200, 1035204, 1040102, 1040200, 1040206, 1040208, 1045205, 1050200, 1060504, 1070500, 1070717, 1075101, 1075202, 1075204, 1075524, 1080500
36555
36555 WASHER, NYLON - INTAKE TUBE SEAL
1007208, 1010208, 1020100, 1020202, 1040102, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203
20262
20262 WASHER, GREASE VENT HOLE SCREW
1003203, 1003209, 1004200, 1005200, 1007208, 1007209, 1010208, 1020100, 1020202, 1020208, 1040102, 1040206, 1045205, 1070717, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203, 1300623
38949
30314
30314 WASHER, NYLON - CHOKE KNOB AND SHAFT
1020100, 1020202, 1035204, 1035207, 1040200, 1040208, 1400100, 1402202, 1402205
49221
49221 WASHER, NEOPRENE - GEAR HOUSING FLUSHING PLUG
1004200, 1020100, 1020202, 1020208, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040206, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302
56720
56720 WASHER, TILT LOCK AND STOP LEVER
1003209, 1006201PD, 1006206, 1006211RD, 1008211RD, 1016207PD, 1020202, 1020208, 1035204, 1035207, 1040200, 1040208, 1050312BC, 1060504, 1070500, 1075217PD, 1075524, 1080500, 1080508, 1100412PD, 11354120D, 1135412MD, 1135412SD, 1150413SD, 1150453JD, 1