851868 1 Mercury WASHER


851868 1 WASHER Mercury 1040203YL, 1040213YL WASHER
851868 1 WASHER Mercury
Rating:
53

Buy WASHER 851868 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

Mercury entire parts catalog list:

1040203YL 2001,2002,2003,2004
1040213YL 2001,2004

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
91-3
Accelerator Pedal Position #1 : Voltage Above Normal 91-3
Throttle Position Sensor : Voltage Above Normal The Electronic Control Module (ECM) detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.
91-4
Accelerator Pedal Position #1 : Voltage Below Normal 91-4
Throttle Position Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.
91-8
Accelerator Pedal Position #1 : Abnormal Frequency, Pulse Width, or Period 91-8
Throttle Position Sensor : Abnormal Frequency, Pulse Width, or Period The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle. Note: Performing steps within this procedure requires the use of a multimeter capable of measuring a PWM duty cycle and frequency.
Table 2
Required Tools
Part Number Part Name Qty
7X-1710 Multimeter Probe 1
146-4080 Digital Multimeter Gp 1
326-4904 Adapter Cable As 1
Table 3
Troubleshooting Test Steps Values Results
1. Check the Signal Frequency and the Duty Cycle at the Sensor
A. Turn the keyswitch to the OFF position.
B. Remove the wire from terminal location C (Throttle position) on the wiring harness side of the connector for the throttle position sensor.
C. Install a 326-4904 Adapter Cable As (3-PIN BREAKOUT) at the connector for the throttle position sensor.
D. Connect the connector for the throttle position sensor.
E. Turn the keyswitch to the ON position.
F. Measure the frequency and the duty cycle at the 326-4904 Adapter Cable As (3-PIN BREAKOUT) between the following terminals:
- B (Digital return) and C (Throttle position)
G. Operate the throttle pedal while making the measurements.
H. Turn the keyswitch to the OFF position.
J. Remove the breakout harness.
K. Restore the wiring harness connector to the original configuration.
Frequency
Duty cycle
Result: The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal. The frequency is below 150 Hz or the frequency is above 1000 Hz. The duty cycle is less than 5 percent or the duty cycle is greater than 95 percent.
Proceed to Test Step 2.
Result: The frequency and the duty cycle are within specifications for the entire range of the pedal.
Repair: Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 2.
2. Check the Supply Voltage to the Sensor
A. Turn the keyswitch to the OFF position.
B. Disconnect the wiring harness connector for the throttle position sensor.
C. Measure the voltage across the following wiring harness connector terminals:
- Terminal A (8 V supply) and Terminal B (Digital return)
7.5 VDC
Result: The supply voltage is above 7.5 VDC at the sensor connector.
Repair: The wiring is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: The supply voltage is not above 7.5 VDC at the sensor connector.
The supply voltage is not reaching the speed control.
Repair: Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts washer Mercury:

49221
 
49221 WASHER, NEOPRENE - GEAR HOUSING FLUSHING PLUG
1004200, 1020100, 1020202, 1020208, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040206, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302
16335
 
16335 WASHER, BAFFLE PLATE SCREW
1002201FM, 1002201VB, 1003201NK, 1004137, 1004201FB, 1004201JK, 1004201VB, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL,
812876
WASHER
812876 WASHER
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412D
825190
WASHER
825190 WASHER
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
804508
WASHER
804508 WASHER
1006201AK, 1006201FK, 1008201YM, 1040203FL, 1040203YL, 1040213YL, 1B04201FB, 1F04201WB
853991
WASHER
853991 WASHER
1030201YL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL
16140 9
 
16140 9 WASHER
1040203FL, 1040203YL, 1040213YL
95392 7
 
95392 7 WASHER
1040203FL, 1040203YL, 1040213YL
Back to top