93224A 1 WATER PUMP COVER (39-PLASTIC)(40) Mercury
1005200, 1007209, 1040100
WATER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
HeuroFosh 46-70941A3 Water Pump Impeller Kit for Mercury Outboard 4 4 4.5 7.5 9.8HP Sierra 18-3446
Heurofosh This Mercury 7.5 water pump kit is for Mercury Mariner Force Outboards || Fit Mercury Mariner Force Outboards 4 4.5 7.5 9.8 HP boat motor parts cooling system, more detailed information please see description below. || Replace: Mercury 46-70941A3, 46893A6, Sierra 18-3446, GLM Marine 12122, SEI Marine 96-260-01AK, This impeller kit makes repair and maintenance of water pumps easy || Package includes: Housing, Water Pump Assembly 70941T01, 70941A 1, Cover 93224A1, Face Plate 46895, Cup, Insert 70977T, 70977, Water Pump Impeller 89981, Key 8M0032835, 56655, Seal 36558, O-ring 25-62704, 29439, Rubber Ring 26-30526, Oil Seal. O ring 26-30913 as pictures showed || To find the correct impeller kits for your boat motor, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages e.g. boat engine model, horsepower or year
Heurofosh This Mercury 7.5 water pump kit is for Mercury Mariner Force Outboards || Fit Mercury Mariner Force Outboards 4 4.5 7.5 9.8 HP boat motor parts cooling system, more detailed information please see description below. || Replace: Mercury 46-70941A3, 46893A6, Sierra 18-3446, GLM Marine 12122, SEI Marine 96-260-01AK, This impeller kit makes repair and maintenance of water pumps easy || Package includes: Housing, Water Pump Assembly 70941T01, 70941A 1, Cover 93224A1, Face Plate 46895, Cup, Insert 70977T, 70977, Water Pump Impeller 89981, Key 8M0032835, 56655, Seal 36558, O-ring 25-62704, 29439, Rubber Ring 26-30526, Oil Seal. O ring 26-30913 as pictures showed || To find the correct impeller kits for your boat motor, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages e.g. boat engine model, horsepower or year
$25.00
05-02-2024
CN: JSPROXAM
JSProxam Water Pump Impeller Kit for Mercury Mariner 4/4.5/7.5/9.8 HP 46-70941A3, 18-3446
JSProxam Replaces part # 46-70941A3, 18-3446 || lf you have any question, please contact us. We will reply immediately.
JSProxam Replaces part # 46-70941A3, 18-3446 || lf you have any question, please contact us. We will reply immediately.
WINGOGO 70941A3 Water Pump Impeller Repair Kit with Housing 93224A1 Replacement for Mercury Mariner Force Outboards 2 Stroke Carb 3.9 4 4.5 6 7.5 9. 8 HP Driveshaft Dia 0.456 IN 46-70941A3 46893A6
WINGOGO This water pump impeller repair kit for Mercury Mariner Force Outboards OEM p/n 46-70841A3 46893A6. it is VERY IMPORTANT to check part number before purchase. please message us year, horsepower and model if you are not sure. || Water pump rebuild kit replacement for Mercury Mariner Force Outboards 3.9HP 4HP 4.5HP 6HP 7.5HP 9.8HP boat motor parts cooling system. more detailed information please see description below. || Compatibale with the outboards Sierra Marine 18-3446, GLM Marine 12122, SEI Marine 96-260-01AK . This impeller kit makes repair and maintenance of water pumps easy. || What is included: Housing, Water Pump Assembly 70941T01, 70941A 1, Cover 93224A1, Face Plate 46895, Cup, Insert 70977T, 70977, Water Pump Impeller 89981, Key 8M0032835, 56655, Seal 36558, O-ring 25-62704, 29439, Rubber Ring 26-30526, Oil Seal. O ring 26-30913 as pictures showed. || To find the correct impeller kits for your boat motor, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages e.g. boat engine model, horsepower or year if you're not sure. we’re pleasure to help you.
WINGOGO This water pump impeller repair kit for Mercury Mariner Force Outboards OEM p/n 46-70841A3 46893A6. it is VERY IMPORTANT to check part number before purchase. please message us year, horsepower and model if you are not sure. || Water pump rebuild kit replacement for Mercury Mariner Force Outboards 3.9HP 4HP 4.5HP 6HP 7.5HP 9.8HP boat motor parts cooling system. more detailed information please see description below. || Compatibale with the outboards Sierra Marine 18-3446, GLM Marine 12122, SEI Marine 96-260-01AK . This impeller kit makes repair and maintenance of water pumps easy. || What is included: Housing, Water Pump Assembly 70941T01, 70941A 1, Cover 93224A1, Face Plate 46895, Cup, Insert 70977T, 70977, Water Pump Impeller 89981, Key 8M0032835, 56655, Seal 36558, O-ring 25-62704, 29439, Rubber Ring 26-30526, Oil Seal. O ring 26-30913 as pictures showed. || To find the correct impeller kits for your boat motor, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages e.g. boat engine model, horsepower or year if you're not sure. we’re pleasure to help you.
Number on catalog scheme: 27
Mercury entire parts catalog list:
- GEAR HOUSING (DRIVE SHAFT) » 93224A 1
- GEAR HOUSING (DRIVE SHAFT) » 93224A 1
- GEAR HOUSING (DRIVE SHAFT) (PAGE 2) » 93224A 1
Information:
1. Remove plug (1) from the fuel injection pump housing.2. Use Tool (D) to loosen nut (2) for the fuel injection pump to be removed. Disconnect the fuel injection line nuts, and remove the felt washer. 3. Install Tool (A) in the fuel pump housing as shown with the square end down. Use a small amount of hand force to push down on Tool (A) while the control lever is moved forward to the "FUEL ON" position. Rack travel will stop in the center (zero) position. Hold a light forward force on the governor control lever to keep the fuel racks in the center (zero) position.4. Use Tool (B) to remove bushing (3) from the fuel injection pump housing. 5. Remove bushing (3) and O-ring seal (4).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed in their original location.
6. Use Tool (C) to remove fuel injection pump (5). 7. Remove spacer (6) from the fuel injection pump housing. Make a note of the position from which each spacer was removed so each spacer can be installed in its original position.
Be careful when the fuel injection pumps are disassembled. Do not damage the surfaces of the plungers, barrels and bonnets. Any scratches will cause leakage inside the fuel injection pump. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. The check assemblies are made as a set. Do not mix the parts of the different check assemblies. Do not remove or make any adjustments of the gear segment on the plunger. It has been preset at the factory. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
8. Disassemble the fuel injection pump as follows: Remove ring (7). Separate bonnet (10) from barrel (9). Remove the spring and the check assembly from the bonnet. Remove plunger (8), the washer and spring from barrel (9).Install Fuel Injection Pumps
1. Inspect all parts for wear or damage. The plunger and barrel are serviced only as an assembly. 2. Put clean diesel fuel on plunger (1). Put plunger (1), washer (6) and spring (2) in position on barrel (3).3. Put check valve assembly (7) and spring (8) in bonnet (9). Connect bonnet (9) and barrel (3) together with ring (4). 4. Put spacer (10) into position in the pump housing bore. Be sure the correct spacer is with each pump. 5. Note the location of dowels (11) and (12) in the fuel injection pump housing. These dowels are for alignment of the fuel injection pump. 6. Slot (13) in gear segment (5) must align with dowel (11).7. Groove (14) must engage with dowel (12). 8. Use Tool (A) to put the fuel racks in the center (zero) position. See Remove Fuel Injection Pumps.9. Use Tool (E) to turn the engine in a counterclockwise direction until the fuel injection pump camshaft lobe is down for the fuel injection pump to be installed. Use Tool (C) to install the fuel injection pump. 10. Install a new O-ring seal (15) and bushing (16) in the fuel injection pump housing bore. If the pump is in the correct position, bushing (16) can be installed with fingers until it is even with the outside surface of the housing. If the bushing cannot be installed as described, remove the fuel injection pump, and repeat Steps 4 through 6. Use Tool (B) to tighten bushing (16) to a torque of 205 14 N m (154 10 lb ft).11. Install the felt washer in the fuel injection pump housing. 12. Connect the fuel injection line to the fuel injection pump. Use Tool (D) to tighten the fuel injection line nuts to a torque of 41 7 N m (30 5 lb ft).13. Check the correct installation of the fuel injection pumps with the engine stopped. See the topic "Fuel Rack Travel".
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
14. Remove Tool (A), and install the plug into the fuel injection pump housing.
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed in their original location.
6. Use Tool (C) to remove fuel injection pump (5). 7. Remove spacer (6) from the fuel injection pump housing. Make a note of the position from which each spacer was removed so each spacer can be installed in its original position.
Be careful when the fuel injection pumps are disassembled. Do not damage the surfaces of the plungers, barrels and bonnets. Any scratches will cause leakage inside the fuel injection pump. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. The check assemblies are made as a set. Do not mix the parts of the different check assemblies. Do not remove or make any adjustments of the gear segment on the plunger. It has been preset at the factory. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
8. Disassemble the fuel injection pump as follows: Remove ring (7). Separate bonnet (10) from barrel (9). Remove the spring and the check assembly from the bonnet. Remove plunger (8), the washer and spring from barrel (9).Install Fuel Injection Pumps
1. Inspect all parts for wear or damage. The plunger and barrel are serviced only as an assembly. 2. Put clean diesel fuel on plunger (1). Put plunger (1), washer (6) and spring (2) in position on barrel (3).3. Put check valve assembly (7) and spring (8) in bonnet (9). Connect bonnet (9) and barrel (3) together with ring (4). 4. Put spacer (10) into position in the pump housing bore. Be sure the correct spacer is with each pump. 5. Note the location of dowels (11) and (12) in the fuel injection pump housing. These dowels are for alignment of the fuel injection pump. 6. Slot (13) in gear segment (5) must align with dowel (11).7. Groove (14) must engage with dowel (12). 8. Use Tool (A) to put the fuel racks in the center (zero) position. See Remove Fuel Injection Pumps.9. Use Tool (E) to turn the engine in a counterclockwise direction until the fuel injection pump camshaft lobe is down for the fuel injection pump to be installed. Use Tool (C) to install the fuel injection pump. 10. Install a new O-ring seal (15) and bushing (16) in the fuel injection pump housing bore. If the pump is in the correct position, bushing (16) can be installed with fingers until it is even with the outside surface of the housing. If the bushing cannot be installed as described, remove the fuel injection pump, and repeat Steps 4 through 6. Use Tool (B) to tighten bushing (16) to a torque of 205 14 N m (154 10 lb ft).11. Install the felt washer in the fuel injection pump housing. 12. Connect the fuel injection line to the fuel injection pump. Use Tool (D) to tighten the fuel injection line nuts to a torque of 41 7 N m (30 5 lb ft).13. Check the correct installation of the fuel injection pumps with the engine stopped. See the topic "Fuel Rack Travel".
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
14. Remove Tool (A), and install the plug into the fuel injection pump housing.
Parts water Mercury:
31940
32077
46893A 6
46893A 3
46893A 3 WATER PUMP HOUSING (40)
1040100, 1040102, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
34293
34293 WATER TUBE
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30593A 1
70941A 1
92970A 1