3C8-84963-0 Nissan BOLT, 3/8-43


3C8-84963-0 BOLT, 3/8-43 Nissan NS40D2, NS40D2, NS40D2, NS50D2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2 BOLT
3C8-84963-0 BOLT, 3/8-43 Nissan
Rating:
73

Buy BOLT, 3/8-43 3C8-84963-0 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 8-3
 

Nissan entire parts catalog list:

NS40D2 2003
NS40D2 2004
NS40D2 2005
NS50D2 2003
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014

Information:


Illustration 1 g00897955
Rear view
Illustration 2 g00897965
Top view
Illustration 3 g00897954
Closed position
(1) Adjusting bolt (2) Thrust washer Width of groove in shaft for thrust washer ... 6.53 0.10 mm (0.2571 0.0039 inch)Thickness of thrust washer ... 6.00 0.05 mm (0.236 0.002 inch) (3) Locking nut (4) Plate (5) Bolt (6) Stop plate (7) Housing Bore in housing for shaft bearings ... 25.402 0.010 mm (1.0001 0.0004 inch)Outside diameter of shaft bearings ... 25.529 0.020 mm (1.0051 0.0008 inch) (8) Shaft (9) Choke plate (10) Bolt (11) Bearing Install the bearings so the lubrication fitting is in an accessible position.Lubricate the bearings with 5P-0960 Molybdenum Grease. (12) Bolt Apply 155-0695 Thread Lock Compound to the threads of the bolts prior to assembly. (13) Bolt Apply 4C-5599 Anti-Seize Compound to the threads and to the face of the bolts. (14) Nut Torque for nuts ... 25 6 N m (18 4 lb ft) (15) Rod Distance between the center bores of the rod ends ... 118 mm (4.646 inch) (16) Clevis Apply 4C-4030 Thread Lock Compound to the threads. (17) Nut Torque for nuts ... 25 6 N m (18 4 lb ft) (18) Nut Torque for nut ... 200 20 N m (150 15 lb ft) (19) Rod Distance between the center bores of the rod ends ... 389 mm (15.315 inch) (20) Actuator (21) Inlet port (22) Outlet port (A) Angle Angle for the lever in the fully closed position ... 27 degrees (B) Angle Angle for the lever in the fully closed position ... 45 degrees (C) Angle Angle for the lever in the fully closed position ... 34 degreesUse the following procedure to assemble the air choke:
Assemble choke plate (9) to shaft (8). Loosely install bolts (10).
Install thrust washer (2) and tighten bolts (5).
To ensure that bolts (10) are properly seated in shaft (8), fully close choke plate (9) and tighten bolts (10).
Make sure that choke plate (9) is fully closed. Loosen locking nut (3) and turn adjusting bolt (1) until the bolt is seated against stop plate (6). Tighten the bolt for an additional 1/4 turn (90 degrees) and then tighten the locking nut.
Assemble the actuator with inlet port (21) in the upward position and with outlet port (22) in the downward position. Tighten nut (18) to the specified torque.
Apply 4C-4030 Thread Lock Compound to the threads of clevis (16).
Assemble rod (15). Provide equal engagement of the threads at both ends of the rod until the distance between the center bores of the rod ends is approximately the specified length.
Assemble rod (19). Provide equal engagement of the threads at both ends of the rod until the distance between the center bores of the rod ends is approximately the specified length.
For final adjustment of the linkage, ensure that the actuator does not try to force stop plate (6) past plate (4) when the choke plate is moved to the fully open position.
Fully extend the actuator. Make sure that the choke plate is in the fully open position and that stop plate (6) contacts plate (4).
Then reduce the length of rod (15) by 1/2 turn (180 degrees). This allows a clearance between stop plate (6) and plate (4).
Make sure that the choke plate can achieve the fully closed position. Tighten nuts (14) and nuts (17) to the specified torque.


Parts bolt Nissan:

916124-0630
 
916124-0630 BOLT
NS2.5A2, NS3.5A2, NS3.5B2, NS4C, NS5B, NS5BS, NSD50A
910103-5625
 
910103-5625 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS3.5A2, NS3.5B2, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD7
910103-6616
 
910103-6616 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS40C, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NS
910114-0625
 
910114-0625 BOLT
NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NS9.9D2, NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B
910103-6630
 
910103-6630 BOLT
NS120A2, NS140A2, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF25A, NSF25B, N
910113-5835
 
910113-5835 BOLT
NS120A2, NS140A2, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B, NSF2.5A, NSF2A, NSF3.5A
3C8-09050-0
 
3C8-09050-0 BOLT, OIL PUMP
NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B
910103-5512
 
910103-5512 BOLT
NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF25B, NSF25B, NSF30B
Back to top