910124-0880 BOLT Nissan
NS8B, NS9.8B
BOLT
Price: query
Rating:
Nissan entire parts catalog list:
- CYLINDER CRANK ASSEMBLY » 910124-0880
- PISTON & CRANK SHAFT » 910124-0880
- PISTON & CRANK SHAFT » 910124-0880
- CYLINDER CRANK ASSEMBLY » 910124-0880
Information:
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add .5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start the engine and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques. Cooling Systems with Heavy Deposits or Plugging
Note: For the following procedure to be effective, there must be some active flow through the cooling system components.
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add .5 L (1 pint) of cleaner per 3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start the engine and run the engine at low idle for a minimum of 90 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques. Fill
Refer to the Operation and Maintenance Manual, "Coolant Specifications" topic for information regarding acceptable water, coolant/antifreeze, and supplemental coolant additive requirements. Refer to the Operation and Maintenance Manual, "Refill Capacities" topic for the capacity of the engine's system.Engines that are Equipped with a Coolant Recovery Tank
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with coolant/antifreeze. Refer to the Operation and Maintenance Manual, "Cooling System Specifications" topic (Maintenance Section) for more information on cooling system specifications. Do not install the c
Parts bolt Nissan:
910103-5618
910103-5625
910103-5625 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS3.5A2, NS3.5B2, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD7
910103-0616
910103-0616 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS40C, NS4C, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NS9.9D2, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15B2, NSF15B2, NSF15C, NSF15C,
910103-5620
910103-5620 BOLT
NS120A2, NS140A2, NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B,
910103-0830
910103-0830 BOLT
NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NSD115A2, NSD50A, NSF4B, NSF5A2, NSF5B, NSF5B, NSF6A2, NSF6B, NSF6B
916103-0830
910103-5640
916129-0675