916114-0830 Nissan BOLT


916114-0830 BOLT Nissan NSF8A2, NSF8A3, NSF9.8A2, NSF9.8A3 BOLT
916114-0830 BOLT Nissan
Rating:
13

Buy BOLT 916114-0830 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

Nissan entire parts catalog list:

NSF8A2 2004,2005
NSF8A3 2006
NSF9.8A2 2004,2005
NSF9.8A3 2006

Information:


Illustration 1 g00839578
(1) Delivery valve holder (2) Spring (3) Delivery valve (4) Fuel injection pump (5) Drain tube
Remove delivery valve holder (1) for the No. 1 cylinder.Note: Some fuel injection pumps may need to be removed to an upright position in order to remove the fuel delivery valve. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".Note: All components of the fuel delivery valve must be kept clean. Keep the components in clean diesel fuel.
Remove delivery valve (3) from the holder.
Reinstall delivery valve holder (1) and spring (2). Tighten the fuel delivery valve to 42 N m (31 lb ft).Note: Fit the fuel injection pump to the engine if the fuel injection pump was removed.
Install drain tube (5) to delivery valve holder (1) for the No. 1 cylinder.
Illustration 2 g00826712
(6) Fuel reservoir (7) Control valve (8) Hose (9) Drain pan (10) Timing mark
Install fuel reservoir (6) with a control valve (7). Install a hose (8) from fuel reservoir (6) to the inlet of fuel injection pump (4). Fill the fuel reservoir with 0.2 L (0.21 qt) of clean fuel.Note: The fuel reservoir should be approximately 152 mm (6 inch) above the fuel injection pump.
Put drain pan (9) below drain tube (5) in order to catch the fuel.
Open control valve (7) for fuel reservoir (6). If the fuel injection pump is set correctly, then the fuel should flow through drain tube (5) .
From the front of the engine, turn the crankshaft in a clockwise direction until the flow of the fuel is reduced to 1 drop for every 7 to 10 seconds. This should be the correct timing mark (10) .
Illustration 3 g00826730
(4) Fuel injection pump (11) Shim
Ensure that the timing mark (10) is correct. Compare the value by timing mark (10) with Table 1.
Table 1
Engine Description     Maximum Rated Engine Speed (RPM)     Injection Timing (BTC)    
C1.5/3013C Genset     1500     14° 1°    
C1.5/3013C Genset     1800     14° 1°    
C1.5/3013C Genset     3000     20° 1°    
C2.2/3024C Genset     1500     15° 1°    
C2.2/3024C Genset     1800     12° 1°    
C2.2/3024C Genset     3000     18° 1°    
If shim (11) must be replaced, remove the fuel injection pump and the shim.The timing will change one degree for each 0.10 mm (0.004 inch) in thickness of the shim. Thicker shims will retard the timing while thinner shims will advance the timing.Install fuel injection pump (4) and a new shim (11) of the correct thickness. Tighten all nuts and bolts to the correct torque. Refer to Specifications for additional information.Note: If a shim is not required, use a thin coat of 4C-9612 Silicone Sealant on the mating surfaces of the fuel injection pump and the cylinder block.
When the timing is correct, remove drain tube (5), fuel reservoir (6), and hose (8) .
Remove delivery valve holder (1). Assemble all of the components of the fuel delivery valve. Install the fuel delivery valve to fuel injection pump (4). Tighten the fuel delivery valve to 42 N m (31 lb ft).
Install all fuel lines in the correct position. Tighten all nuts and bolts to the correct torque. Refer to Specifications for the correct torque.
Install the fuel shutoff solenoid.
Eliminate air from the fuel system.
The engine must be tested on an engine dynamometer in order to check the maximum no-load speed and engine settings after assembly.


Parts bolt Nissan:

910103-5625
 
910103-5625 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS3.5A2, NS3.5B2, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD7
910103-0616
 
910103-0616 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS40C, NS4C, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NS9.9D2, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15B2, NSF15B2, NSF15C, NSF15C,
910103-5620
 
910103-5620 BOLT
NS120A2, NS140A2, NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B,
910113-5652
 
910113-5652 BOLT
NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS9.9D2, NSF15B2, NSF15B2, NSF18B2, NSF18B2, NSF25A, NSF25B, NSF30A, NSF30B, NSF8A, NSF8A2, NSF8A3, NSF9.8A, NSF9.8A2, NSF9.8A3, NSF9.9B2, NSF9.9B2
910114-5635
 
910114-5635 BOLT
NSD115A, NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF2.5A, NSF20C, NSF20C, NSF2A, NSF3.5A, NSF8A, NSF8A2, NSF8A3, NSF9.8A, NSF9.8A2, NSF9.8A3, NSF9.9B2, NSF9.9B2, NSF9.9C
3H8-01012-0
 
3H8-01012-0 BOLT, 8 - 50
NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF20C, NSF20C, NSF8A, NSF8A2, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9.8A, NSF9.8A2, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.9B2, NSF9.9B2, NSF9.9C
3C8-84964-0
 
3C8-84964-0 BOLT, 3/8-35
NS40D2, NS40D2, NS40D2, NS50D2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSF8A2, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9.8A2, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
910103-5630
 
910103-5630 BOLT
NS120A2, NS140A2, NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF25B, NSF25B, NSF25B, NSF30B, NSF30B, NSF4B, NSF4B, NSF4C, NSF5B, NSF5B, NSF5C, NSF6B, NSF6B, NSF6C, NSF8A2, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9
Back to top