916124-0840 Nissan BOLT


916124-0840 BOLT Nissan NS120A2, NS140A2, NS25C3, NS30A4, NS40C, NSD115A, NSD115A2 BOLT
916124-0840 BOLT Nissan
Rating:
88

Buy BOLT 916124-0840 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Compatible models:

Nissan entire parts catalog list:

NS120A2 2003,2004,2005
NS140A2 2003,2004,2005
NS25C3 2003,2005
NS30A4 2003
NS40C 2004
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014

Information:


Illustration 1 g00743757
Schematic for the air shutoff system
Illustration 2 g01080666
Terminal locations for ECM connectorTest Step 1. Check the Electrical Connectors and the Wiring
Verify that the air shutoff valves are set to the Open position.
Thoroughly inspect the ECM connector J1/P1, and the customer connector. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit for the remote shutdown switch.
Check the ECM connector (allen head screw) for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the customer connector (allen head screw) for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points from the air shutoff solenoid to the ECM.Refer to Illustration 1 for terminal locations for the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the wiring and connectors or replace the wiring or the connectors. Ensure that all of the seals are properly connected. Verify that the repair eliminates the problem.STOPTest Step 2. Test for Voltage from the Normally Open Contacts of the Air Shutoff Relay
Place the engine control in the OFF/RESET mode.
Remove the wire from the normally open contacts of the air shutoff relay that goes to the air shutoff solenoid.
Connect the test lamp at the normally open contact of the air shutoff relay that goes to the air shutoff solenoid. Connect the other lead of the test lamp to engine ground.
Place the engine control in the ON mode and start the engine.
Activate the overspeed verify switch.
Increase the engine speed past 75 percent of the programmed overspeed setpoint, and monitor the test lamp.
Place the engine control in the OFF/RESET mode.
Replace all wires to the normal configuration.Expected Result:The test lamp illuminates and stays illuminated.Results:
OK


Parts bolt Nissan:

910103-5625
 
910103-5625 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS2.5A2, NS3.5A2, NS3.5B2, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD7
910113-5620
 
910113-5620 BOLT
NS120A2, NS140A2, NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS9.9D2, NSD115A, NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B, NSF15B2, NSF15B2, NSF18B2, NSF18B2, NSF2.5A, NSF25A, NSF25B, N
910113-5610
 
910113-5610 BOLT
NS25C3, NS30A4, NS40C, NSF8A, NSF9.8A
910103-6830
 
910103-6830 BOLT
NS15D2, NS18E2, NS25C3, NS30A4, NS9.9D2
910113-5618
 
910113-5618 BOLT
NS40C, NSF25A, NSF25B, NSF30A, NSF30B
916189-0835
 
916189-0835 BOLT, 8-35
NS120A2, NS140A2, NS60C, NS70C, NSD115A, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B, NSF50B, NSF50B
910103-0845
 
910103-0845 BOLT
NS120A2, NS140A2, NS60C, NS70C
3C7-61017-1
 
3C7-61017-1 BOLT, 10-107
NS120A2, NS140A2, NSD115A
Back to top