353-63207-0 COLLAR, 10.2-12-12 Nissan
NS120A2, NS140A2, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD115A2, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15C, NSF20C, NSF25A, NSF25B, N
COLLAR

Price: query
Rating:
Compatible models:
Nissan entire parts catalog list:
- BRACKET-FOR NEW PTT » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET-FOR NEW PTT » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- STEERING HANDLE (FOR F TYPE) » 353-63207-0
- BRACKET (1) (FOR PTT) » 353-63207-0
- BRACKET (1) (FOR PTT) » 353-63207-0
- STEERING HANDLE (FOR F TYPE) » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET 2, POWER TRIM & TILT » 353-63207-0
- BRACKET 2, POWER TRIM & TILT » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET (2) POWER TRIM & TILT (NEW) » 353-63207-0
- BRACKET 2, POWER TRIM & TILT » 353-63207-0
- BRACKET 2, POWER TRIM & TILT » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET » 353-63207-0
NSD75C2 2010,2011,2012,2013,2014
- BRACKET » 353-63207-0
- BRACKET » 353-63207-0
- BRACKET » 353-63207-0
NSD90C2 2010,2011,2012,2013,2014
- BRACKET » 353-63207-0
- BRACKET PTT » 353-63207-0
- BRACKET PTT » 353-63207-0
- GAS ASSIST, POWER TRIM & TILT » 353-63207-0
- BRACKET, PTT & GAS ASSISTANT » 353-63207-0
- BRACKET PTT AND GAS ASSIST » 353-63207-0
- BRACKET (PTT GAS ASSIST) » 353-63207-0
- GAS ASSIST, POWER TRIM & TILT » 353-63207-0
- BRACKET, PTT & GAS ASSISTANT » 353-63207-0
- BRACKET PTT AND GAS ASSIST » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET, EFT & EPT TYPE » 353-63207-0
- BRACKET, EFT & EPT TYPE » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET, EFT & EPT TYPE » 353-63207-0
- BRACKET (FOR "EFT & EPT" TYPE) » 353-63207-0
- BRACKET, EFT & EPT TYPE » 353-63207-0
Information:
This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Illustration 1 g00363480
Valve lash
Table 1
Valve Lash
Valves Acceptable Range for Valve Lash
Inlet
0.38 0.08 mm (0.015 0.003 inch)
Exhaust
0.76 .08 mm (0.030 0.003 inch) If the measurement is not within this range adjustment is necessary. Refer to Testing And Adjusting, "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 2 g00363481
Valve adjustment
Illustration 3 g00797249
(A) Inlet valves (B) Exhaust valves
Table 2
Valve Lash
Valves Dimension of the Gauge
Inlet
0.38 mm (0.015 inch)
Exhaust
0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves.Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base circle.
Make an adjustment to the valve lash on the inlet valves for cylinders 1, 3, 4, 6, 7 and 12.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves for cylinders 1, 4, 5, 8, 9, and 12.
Loosen valve adjustment locknut (1) .
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt, and turn the flywheel by 360 degrees in the direction of engine rotation. This will position the No. 7 piston at the top center on the compression stroke. Install the timing bolt in the flywheel.
Make an adjustment to the valve lash on the inlet valves 2, 5, 8, 9, 10, and 11.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves 2, 3, 6, 7, 10, and 11.
Loosen valve adjustment locknut (1) .
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt from the flywheel after all valve lash adjustments have been made.
Parts collar Nissan:
3R1-05215-0
3R1-05215-0 COLLAR, 6.1 - 8 - 6.5
NS4C, NS5B, NS5BS, NSF4B, NSF4B, NSF4C, NSF5B, NSF5B, NSF5C, NSF6B, NSF6B, NSF6C, NSF8A, NSF8A2, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9.8A, NSF9.8A2, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
3A0-76079-0
3A0-76079-0 COLLAR, 8.2 - 9 - 7.5
NS25C3, NS30A4, NS40C, NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF2.5A, NSF2.5B, NSF2.5B, NSF20C, NSF20C, NSF25A, NSF25B, NSF25B, NSF25B, NSF2A, NSF2B, NSF3.5A, NSF3.5B, NSF3.5B, NSF30A, NSF30B, NSF30B, NSF4A2, NSF4B, NSF4B, NSF4C, NSF5A2
3H6-63619-1
3H6-63619-1 COLLAR, BRACKET
NSD115A, NSD115A2, NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF20C, NSF20C, NSF4A2, NSF4B, NSF4B, NSF5A2, NSF5B, NSF5B, NSF6A2, NSF6B, NSF6B, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.9B2, NSF9.9B2, NSF9.
3C8-77185-0
3C8-77105-0
3C8-77105-0 COLLAR, CYLINDER PIN LOWER
NS40D2, NS40D2, NS40D2, NS50D2, NSD40A, NSD40B, NSD50A, NSD50B
3B7-77174-0
3AC-63619-0
3T1-10042-0
3T1-10042-0 COLLAR, 13.5 - 25 - 13
NSD115A, NSD115A2, NSD40B2, NSD40B2, NSD50B2, NSD50B2, NSD70B, NSD75C2, NSD90B, NSD90C2