345-03292-0 Nissan DRAIN SCREW


345-03292-0 DRAIN SCREW Nissan NS120A2, NS140A2, NS25C3, NS30A4, NS40C, NS60C, NS70C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2 DRAIN
345-03292-0 DRAIN SCREW Nissan
Rating:
13

Buy DRAIN SCREW 345-03292-0 Nissan genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$13.69

07-03-2025

CN: Marine Parts Manufac
Outboard Engine 345-03292-0 345032920 345032920M Drain Screw with Seal for Tohatsu for Nissan 25HP 30HP 60HP 70HP 80HP 90HP 115HP 140HP
SouthMarine Fit Engine: 25HP 30HP 60HP 70HP 80HP 90HP 115HP 140HP || Fit Part Number: 345-03292-0 345032920 345032920M || If you are unsure, please provide your engine serial number.
$9.56
 

08-05-2019
13 Hundredths Pounds
Tohatsu: Tohatsu
Tohatsu 345-03292-0 Drain Screw QTY 1
Genuine OEM Tohatsu Part || OEM Tohatsu 345-03292-0 Drain Screw QTY 1 || Part Number: 345-03292-0 || Quantity: 1 || May not include original package.
Number on catalog scheme: 1-17
 

Nissan entire parts catalog list:

NS120A2 2003,2004,2005
NS140A2 2003,2004,2005
NS25C3 2003,2005
NS30A4 2003
NS40C 2004
NS60C 2003
NS70C 2003
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014
NSD70B 2003,2004,2005,2007,2008,2009
NSD70B 2006
NSD70B 2010
NSD75C2 2010,2011,2012,2013,2014
NSD90B 2003,2004,2005,2007,2008,2009
NSD90B 2006
NSD90B 2010
NSD90C2 2010,2011,2012,2013,2014

Information:


Table 1
Valve Lash Check: Engine Stopped    
Inlet     0.38 0.10 mm (0.015 0.004 inch)    
Exhaust    
1.02 0.10 mm (0.040 0.004 inch)    If the measurement is not within tolerance, adjust the valve bridge and then adjust the valve lash.Valve Bridge Adjustment
When the head is disassembled, mark the valve bridges for the respective cylinders. Adjustment of the bridge will be necessary after grinding of the valves or other reconditioning of the cylinder head.The valve bridge must be adjusted before the valve lash is adjusted. The valve bridge can be adjusted without removal of the rocker arms and shafts.Use the following procedure to adjust the valve bridges:
Remove the valve cover.
Ensure that the No. 1 piston is at the top center (TC) position. Refer to Testing And Adjusting, "Finding the Top Center Position for the No. 1 Piston".
Work on the appropriate cylinders that are listed in Testing and Adjusting, "Crankshaft Positions for Valve Lash Setting".
Illustration 1 g00746680
(1) Ignition harness (2) Transformer
Disconnect ignition harness (1) .
Grasp transformer (2) and pull the transformer straight out of the cylinder head.
Illustration 2 g00746697
(3) Locknut (4) Adjustment screw (5) Valve bridge (6) Rocker arm
Illustration 3 g00820226
(3) Locknut (4) Adjustment screw (5) Valve bridge (6) Rocker arm (7) Bridge dowelNote: If the cylinder head is disassembled, keep the valve bridges with the respective valves. Check that bridge dowels (7) are installed to the correct height. Lubricate the bridge dowel, the bore for the bridge dowel, and the top contact surface of the valve bridge. Install the valve bridge on the dowel.
Loosen locknut (3) and adjusting screw (4) .
Press straight down on rocker arm (6) at the contact point for valve bridge (5) . Turn adjusting screw (4) clockwise until the screw just contacts the valve stem.
Tighten adjusting screw (4) for an additional 25 5 degrees in order to straighten the valve bridge onto the dowel.This also compensates for slack in the threads of the adjustment screw.
Hold adjusting screw (4) in position and tighten locknut (3) to 47 9 N m (35 7 lb ft).
Ensure that the valve lash is correct. Refer to "Valve Lash Check".
Install transformer (2) .
Connect ignition harness (1) .
Install the valve cover.Valve Lash Adjustment
The valve bridge must be adjusted before the valve lash is adjusted.
Ensure that the No. 1 piston is at the top center (TC) position. Refer to Testing And Adjusting, "Finding the Top Center Position for the No. 1 Piston".
Work on the appropriate cylinders that are listed in Testing and Adjusting, "Crankshaft Positions for Valve Lash Setting".
Illustration 4 g00769478
(1) Locknut (2) Adjustment screw (3) Rocker arm (4) Wear seat
Loosen locknut (1) and adjusting screw (2) .
Insert the appropriate feeler gauge between rocker arm (3) and wear seat (4) . Refer to Table 3.
Table 2
Valve Lash Setting: Engine Stopped    
Inlet    
0.38 0.10 mm (0.015 0.004 inch)    
Exhaust    
1.02 0.10 mm (0.040 0.004 inch)    
Hold adjusting screw (2) in place and tighten locknut (1) to a torque of 30 4 N m (22 3 lb ft).
Verify that the setting is correct.
Remove the timing bolt from the flywheel housing. Rotate the crankshaft for 360 degrees. Install the timing bolt in the flywheel housing.
With the No. 1 piston in the top center of the opposite stroke, perform Steps 1 through 7 for the remaining cylinders.
Remove the timing bolt from the flywheel housing.


Parts drain Nissan:

3B7-67179-0
 
3B7-67179-0 DRAIN PLUG B, ENGINE BASE
NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3C7-03292-0
 
3C7-03292-0 DRAIN SCREW
NS120A2, NS140A2
Back to top