369-64301-0 Nissan DRIVE SHAFT "S"


369-64301-0 DRIVE SHAFT "S" Nissan NS4C, NS5B, NS5BS, NSF4A2, NSF4B, NSF4B, NSF4C, NSF5A2, NSF5B, NSF5B, NSF5C, NSF6A2, NSF6B, NSF6B, NSF6C DRIVE
369-64301-0 DRIVE SHAFT "S" Nissan
Rating:
23

Buy DRIVE SHAFT "S" 369-64301-0 Nissan genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$115.99
 

23-08-2023

-: -
WATERLONG Drive Shaft Short 369-64301-0 Replacement for TOHATSU Nissan Outboard M NS 4HP 5HP 6HP 2/4T
Replaces TOHATSU NISSAN 369-64301-0 || Fits For TOHATSU NISSAN Outboard M NS 4HP 5HP 6HP 2/4T || The DRIVE SHAFT SHORT meets or exceeds OEM specifications || Easy To Install No Instruction || Boat Motor for Outboard Engine
Number on catalog scheme: 10
 

Nissan entire parts catalog list:

NS4C 2003
NS5B 2003
NS5BS 2003
NSF4A2 2003,2004,2005
NSF4B 2005,2006,2007,2008,2009
NSF4B 2010
NSF4C 2011,2012,2013,2014
NSF5A2 2003,2004,2005
NSF5B 2005,2006,2007,2008,2009
NSF5B 2010
NSF5C 2011,2012,2013,2014
NSF6A2 2003,2004,2005
NSF6B 2005,2006,2007,2008,2009
NSF6B 2010
NSF6C 2011,2012,2013,2014

Information:


Table 1
Revision Summary of Changes
05 Modified introduction and replaced engine software part number.
04 Included Jumper Harness details
03 Introduction text has changed
02 Modified entire core document.
01 Added 380-7362 Tee Adapter part number to the required parts table and quantity of 216-8579 O-Ring Seal changed to two. Introduction
This Special Instruction describes the procedure for installing the new dual sensor coolant protection on certain D11T machine engines. Installation of the "Dual Sensor Coolant Protection" system protects the engine and cooler in the event of a coolant loss.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person must also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance of a potential hazard.Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Avoid using a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar.Ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures.
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
When removing a major component or attachment, ensure that it is properly blocked or secured before removing mounting hardware. An assembly that is disconnected without proper blocking may shift or fall, resulting in serious injury or death of personnel or machine damage.
Personal injury or death can result from improper maintenance procedures. To avoid injury or death, follow the procedures exactly as stated below.
Personal injury or death can result from sudden movement.Prevent possible injury by performing the following procedures before work begins:Move the product or equipment to a smooth, level surface.When applicable, lower equipment/work tools to the ground.Engage the parking brake, system brakes and/or hydraulic lockout control. When applicable, stop the engine and remove the ignition key.Release system pressure from pressurized systems.If applicable, block the wheels/tracks.Turn the battery disconnect switch to the OFF position and if applicable, remove the battery disconnect key. If not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps. Attach a “Do Not Operate” or similar warning tag at the battery disconnect switch location and as defined by site rules and/or local regulations.
Illustration 1 g06276183
Access to this service point may require climbing on the equipment. Slipping or falling while climbing on the equipment could result in personal injury or death. Refer to the Operation and Maintenance Manual, Mounting and Dismounting topic for safety information.
Failure to use an approved access system during installation and removal of components could result in slipping and falling which could result in personal injury or death. To prevent injury or death, use an approved access system to reach the appropriate mounting locations of the components. Do not climb on the machine. Maintain three-points of contact and/or use a safety harness.


Parts drive Nissan:

369S61020-2
369S61030-2
369-64303-0
 
369-64303-0 DRIVE SHAFT "UL"
NS4C, NS5B, NS5BS, NSF4B, NSF4B, NSF4C, NSF5B, NSF5B, NSF5C, NSF6B, NSF6B, NSF6C
369-64302-0
 
369-64302-0 DRIVE SHAFT "L"
NS4C, NS5B, NS5BS, NSF4A2, NSF4B, NSF4B, NSF4C, NSF5A2, NSF5B, NSF5B, NSF5C, NSF6A2, NSF6B, NSF6B, NSF6C
3H6S61020-0
 
3H6S61020-0 DRIVE SHAFT HOUSING 8
NSF4A2, NSF5A2, NSF6A2
3H6Q61020-2
3H6Q61030-3
3ASQ61030-2
Back to top