3C8-01303-4 Nissan ENGINE BASEMENT GASKET


3C8-01303-4 ENGINE BASEMENT GASKET Nissan NSD40B2, NSD40B2, NSD50B2, NSD50B2 ENGINE
3C8-01303-4 ENGINE BASEMENT GASKET Nissan
Rating:
63

Buy ENGINE BASEMENT GASKET 3C8-01303-4 Nissan genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$14.50
 

09-12-2023

SG: ITACO STORE
Boat Motor 3C8-01303 27 812939024 812939016-24 Base Gasket Replaces Nissan Tohatsu Mercury Outboard 40HP-50HP 2-stroke
ITACO 100% Made in Taiwan Quality || Replaces Nissan Tohatsu Outboard part number: 3C8-01303-0M, 3C8-01303-1M, 3C8-01303-2M, 3C8-01303-3M, 3C8-01303-4M (IMPT: check OEM part number before purchase!!) || For Mercury Mercuiser Quicksilver part number: 27 812939021, 27 812939016, 27 8129397, 27 812939024 || Base Gasket || Boat Motor for Outboard Engine
$28.72
 

24-03-2019
13 Hundredths Pounds
Tohatsu: Tohatsu
Tohatsu 3C8-01303-4 Powerhead Base Gasket QTY 1
Genuine OEM Tohatsu Part || OEM Tohatsu 3C8-01303-4 Powerhead Base Gasket QTY 1 || Part Number: 3C8-01303-4 || Quantity: 1 || May not include original package.
£19.99
 

22-09-2017

recmar: recmar
recmar BASE GASKET FOR TOHATSU OUTBOARD 40 50 HP 2 STROKE 3C8-01303-4
2 stroke, aluminium propeller, base gasket, tohatsu outboard 40 hp, tohatsu outboard 50 hp
Number on catalog scheme: 3
 

Compatible models:

NSD40B2   NSD50B2   Nissan

Nissan entire parts catalog list:

NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50B2 2010
NSD50B2 2011,2012,2013,2014

Information:


Illustration 1 g06326972
Rear view of engine
Illustration 2 g03155497
Cam gear bolt tightening sequence
Table 1
Item Qty Part Specification Description
1 1 230-6202 Idler Gear As Before assembly, lubricate the shaft, the bearing bore, and the thrust faces with clean engine oil.
After installation, bore in the 224-9664 Bushing is 71.035 0.013 mm (2.7967 0.0005 inch).
Installation depth of the bushing is 2.6 0.5 mm (0.10 0.02 inch).
2 6 5B-0213 Bolt Torque to 55 10 N m (41 7 lb ft).
3 1 245-3804 Bolt Torque to 55 10 N m (41 7 lb ft).
4 12 6J-3913 Bolt Tighten bolt in the sequence 1, 4, 2, 5, 3, 6, 1, 4 as per Illustration 2 to 240 40 N m (177 30 lb ft).
5 2 331-6188 Camshaft Gear As Before assembly, lubricate the shaft, the bearing bore, and the thrust faces with clean engine oil.
With the number one piston in the top dead center position, align the timing marks. The mark on the camshaft gear must be in alignment with the mark in the rear housing.
6 1 185-1497 Idler Gear As Before assembly, lubricate the shaft, the bearing bore, and the thrust faces with clean engine oil.
After installation, bore in the 224-9664 Bushing is 71.035 0.013 mm (2.7967 0.0005 inch).
Installation depth of the bushing is 2.6 0.5 mm (0.10 0.02 inch).
7 4 1A-2029 Bolt Torque to 55 10 N m (41 7 lb ft).
8 1 226-6036 Idler Gear As Before assembly, lubricate the shaft, the bearing bore, and the thrust faces with clean engine oil.
With the number one piston in the top dead center position, align the timing marks. The mark on the idler gear must be in alignment with the mark on the crankshaft gear (9).
After installation, bore in the 226-6052 Bushing is 88.090 0.013 mm (3.4681 0.0005 inch).
Installation depth of the bushing is 3.2 0.5 mm (0.13 0.02 inch).
9 1 228-5813 Crankshaft Gear As Before assembly, lubricate the shaft, the bearing bore, and the thrust faces with clean engine oil.
Illustration 3 g06327033
Table 2
Item Qty Part Specification Description
10 1 224-1220 Plate Install the plate with the side marked "OUT" away from the gear face.
Thickness is 8.0 0.5 mm (0.31 0.02 inch).
11 8 7B-3235 Bolt Torque to 135 20 N m (100 15 lb ft).
12 2 117-8801 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
13 2 5P-8429 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
14 2 5F-7403 Lockwasher Torque to 406 68 N m (299 50 lb ft) and bend the tab on the lock which aligns with a nut slot.
15 2 5F-7404 Bearing Locknut
16 1 229-1663 Thrust Plate Install the thrust plate with the side marked "OUT" away from the gear face.
Thickness is 6.35 0.25 mm (0.250 0.010 inch).
17 1 4N-0848 Wear Sleeve Before assembly, lubricate the sleeve inner diameter with Loctite® 620.


Parts engine Nissan:

3T5Q01301-0
 
3T5Q01301-0 ENGINE BASEMENT
NSD40B, NSD40B2, NSD40B2, NSD50B, NSD50B2, NSD50B2
3GFB87090-1
 
3GFB87090-1 ENGINE SHORT BLOCK KIT
NSD40B2, NSD40B2, NSD50B2, NSD50B2
Back to top