3T9-76062-0 Nissan FUSE HOLDER


3T9-76062-0 FUSE HOLDER Nissan NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B FUSE
3T9-76062-0 FUSE HOLDER Nissan
Rating:
48

Buy FUSE HOLDER 3T9-76062-0 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

Nissan entire parts catalog list:

NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0288 Head 1
416-0292 Adapter 1 Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install suitable plugs to the inlet ports of the cylinder head in order to prevent the entry of loose parts into the engine.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Note: The following procedure should be adopted in order to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at the top center position before the valve spring is removed. Failure to ensure that the piston is at the top center position may allow the valve to drop into the cylinder bore.
Illustration 1 g03341307
Follow Step 1.a through Step 1.d in order to position the appropriate piston at top center.
Install Tooling (A) in position on the cylinder head in order to compress a valve spring for the appropriate piston.
Use Tooling (A) in order to compress valve spring (3) and open the valve slightly. Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.
Carefully rotate the crankshaft until the piston touches the valve. Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top center position. The valve is now held in a position that allows the valve spring to be safely removed.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Note: The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Apply sufficient pressure to Tooling (A) in order to allow removal of the valve keepers (1). Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.
Remove valve keepers (1).
Slowly release the pressure on Tooling (A).
Remove valve spring retainer (2) and remove valve spring (3).
Remove Tooling (A). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0288 Head 1
416-0292 Adapter 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft while the valve springs are removed.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Install suitable plugs to the inlet ports of the cylinder head in order to prevent the entry of loose parts into the engine.


Parts fuse Nissan:

3T5-76066-0
 
3T5-76066-0 FUSE HOLDER B
NSD40A, NSD40B, NSD40B, NSD50A, NSD50B, NSD50B
3T5-76246-0
 
3T5-76246-0 FUSE, 15A
NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3T5-76249-0
 
3T5-76249-0 FUSE, 30A
NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15C, NSF20C
3T5-76248-0
 
3T5-76248-0 FUSE, 25A
NSD115A, NSD40B, NSD40B, NSD50B, NSD50B, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B
3Z5-76066-0
 
3Z5-76066-0 FUSE HOLDER B (EFO TYPE)
NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50B, NSD50B, NSD50B2, NSD50B2
3Y9-76062-0
 
3Y9-76062-0 FUSE HOLDER
NSD40B, NSD50B, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B
Back to top