3V1-02104-0 Nissan GASKET, INTAKE MANIFOLD

Connecting Rod Bearings
The connecting rod bearings fit tightly in the bore in the rod. If the bearing joints or backs are fretted, check the bore size. This can be an indication of wear because of a loose fit.Connecting rod bearings are available with 0.63 mm (0.025 inch) and 1.27 mm (0.050 inch) smaller inside diameter than the original size bearing. These bearings are for crankshafts that have been ground smaller than the original size.Main Bearings
Main bearings are available with a larger outside diameter than the original size bearings. These bearings are available for the cylinder blocks with the main bearing bore that is made larger than the bores' original size. The size that is available has a 0.63 mm (0.025 inch) outside diameter that is larger than the original size bearings.Cylinder Block
Illustration 1 g00294303
1P-3537 Dial Bore Gauge Group If the main bearing caps are installed without bearings, the bore in the block for the main bearings can be checked. Tighten the nuts that hold the caps to the torque that is shown in the Specifications. Alignment error in the bores must not be more than 0.08 mm (0.003 inch). Refer to the Special Instruction, SMHS7606.Projection Of Cylinder Liners
Table 1
Tools Needed    
Part Number     Description     Quantity    
8B-7548     Push-Puller     1    
3H-0465     Plate     3    
1P-2396     Puller Plate     1    
3/4 - 16 177.8 mm 7.0 inch long     NF Bolt     2    
3/4 - 16 76.2 mm 3.0 inch long     NF Bolt     4    
2F-0126     Seals     8    
8T-0455     Liner Projection Tool Group     1    
8S-3140     Cylinder Block Counterboring Tool     1    
Illustration 2 g00332134
Holding the top plate to the cylinder block (1) 3H-0465 Push Puller Plate. (2) 1P-2396 Puller plate. (3) 2F-0126 Seal. (4) Top plate.Use the following steps to check the liner projection above the top plate.
Ensure that the top plate (4) and the cylinder liner flange are clean.
Install a new spacer plate gasket.
Install the cylinder liners in the cylinder block without seals or bands.
Use 3/4 - 16 NF bolts that are 76.2 mm (3.0 inch) long. Use two 2F-0126 Seals (3) on each bolt. These seals will hold the top plate (4) to the cylinder block. Install two bolts with seals (3). Install the bolts on each side of the cylinder liner. Use the following four steps to tighten the bolts.Tighten the bolts to the following torque. ... 14 N m (10 lb ft)Tighten the bolts again to the following torque. ... 35 N m (26 lb ft)Tighten the bolts again to the following torque. ... 70 N m (52 lb ft)Tighten the bolts again to the following torque. ... 95 N m (70 lb ft)Note: Install two bolts with washers on each side of each cylinder liner. Install the bolts along the complete length of the top plate. This will keep the installation and removal of the bolts and washers to a minimum as each liner is checked.
Use the following items to hold the liner down.
1P-2396 Puller Plate (2)
three 3H-0465 Push Puller Plates (1)
8B-7548 Push-Puller Tool Group (6)
two 3/4 - 16 NF bolts 177.8 mm (7.0 inch) in length
Use the following four steps to tighten the bolts evenly.Tighten the bolts to the following torque. ... 7 N m (62 lb in)Tighten the bolts again to the following torque. ... 20 N m (15 lb ft)Tighten the bolts again to the following torque. ... 35 N m (26 lb ft)Tighten the bolts again to the following torque. ... 70 N m (52 lb ft)The distance from the bottom edge of the 8B-7548 Push Puller Tool Group (6) to the top plate must be equal on both sides of the cylinder liner.
Illustration 3 g00332135
Measuring the liner height projection (5) Dial indicator. (6) 8B-7548 Push Puller Tool Group. (7) 1P-2402 Gauge Body .
The 8T-0455 Liner Projection Tool Group can be used to measure the liner projection. The Special Instruction, SMHS7727 is included with this group.
Mount the indicator (5) in the 1P-2402 Gauge Body (7). Zero the indicator (5) by using the back of the 1P-5507 Gauge Block .
Record measurements for each cylinder.
Find the average reading. Add the four readings for each cylinder and divide the sum of the readings by four.Flywheel And Flywheel Housing
Table 2
Tools Needed     Quantity    
8T-5096     Dial Indicator Group     1    Face Runout (Axial Eccentricity) Of The Flywheel