3G2-06040-2 Nissan IGNITION COIL (WITH RESISTANCE CAP)


3G2-06040-2 IGNITION COIL (WITH RESISTANCE CAP) Nissan NS15D2, NS18E2, NS9.9D2 IGNITION
3G2-06040-2 IGNITION COIL (WITH RESISTANCE CAP) Nissan
Rating:
28

Buy IGNITION COIL (WITH RESISTANCE CAP) 3G2-06040-2 Nissan genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$45.97

28-02-2025
0.1102[0.05] Pounds
CN: zhengzhouxiongpansha
3G2-06040-2 Ignition Coil For 9.9HP NS9.9D2 15HP NS15D2 18HP NS18E2 25HP NS25C2 30HP NS30A3 NS30A4 Mercury 15HP 18HP
WKNYSYK Made of quality material, it is safe and durable to use. || Reasonable price || Simple installation, no complicated tools required, save time and effort. || Precision manufacturing makes it has stable performance || reliable performance and long service life.
$39.99

28-02-2025

CN: CUPP
EUPLI Ignition Coil for Tohatsu 9.9HP 15HP 18HP 3G2-06040-2 3G2-06040 3M3-06048-2 3G2060402 3M3060482 3G2060402M 3M3060482M
EUPLI Fitment: Fit for Tohatsu for 9.9HP 15HP 18HP. || Replaces Part OEM Number#:3G2-06040-2 3M3-06048-2 3G2060402 3M3060482 3G2060402M 3M3060482M || Professional manufacturing, has a long service. || Material: Made of high quality plastic material, wear resistant and durable. || Directly replace the old or broken one.
$63.45

02-02-2025
0.1102[0.05] Pounds
CN: bieshuangwangluokeji
SPTBMDJ Motorcycle Parts 3G2-06040-2 Ignition Coil for NIS/san 9.9HP NS9.9D2 15HP NS15D2 18HP NS18E2 25HP NS25C2 30HP NS30A3 NS30A4 15HP 18HP
SPTBMDJ High quality products || Easy to install and r eplace || Elegant and practical products || Simple and fast installation || The product is exquisite and durable.
Number on catalog scheme: 7
 

Compatible models:

Nissan entire parts catalog list:

NS15D2 2003
NS18E2 2003
NS9.9D2 2003

Information:

Recommended Actions
Perform the following diagnostic procedures in order:Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high rpm, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Check for an individual malfunctioning cylinder.
Ensure that the J300/P300 electronic unit injector connector is fully connected and ensure that the connector is free of corrosion.
Ensure that the J2/P2 ECM connector is fully connected and ensure that the J2/P2 ECM connector is free of corrosion.
Connect the Caterpillar Electronic Technician (Cat ET). Access the "Cylinder Cutout Test" by selecting "Diagnostic Tests" under the "Diagnostics" menu. Run the "Cylinder Cutout Test" in order to disable each cylinder. Disabling each cylinder allows the technician to isolate the misfiring cylinders.If the misfiring cylinder can be isolated to a specific cylinder, refer to Troubleshooting, "Injector Solenoid Circuit - Test".
Check the fuel supply.
Monitor the exhaust for smoke while the engine is being cranked.If white smoke is present, there may be a problem with the fuel quality.
Check the fuel quality. Refer to Testing and Adjusting, "Fuel Quality - Test".
Check the fuel pressure. Refer to Testing and Adjusting, "Fuel System Pressure - Test".
Ensure that the fuel system has been primed. Refer to Testing and Adjusting, "Fuel System - Prime".
Check for fuel supply lines that are restricted.
Check the fuel filters.
If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
Check for air in the fuel system. Refer to Testing and Adjusting, "Air in Fuel - Test".
If the problem does not occur during cruise control, check the accelerator pedal position sensor.
Use the Cruise/Idle On/Off Switch to put the engine in idle mode.
Vary the engine rpm with the Set/Resume switches.If both of the following conditions are met, connect Cat ET and monitor the status of the accelerator pedal position sensor.
The engine is stable by using idle mode to control the engine rpm.
The engine is unstable by using the accelerator pedal position sensor.If the status of the accelerator pedal position sensor is unstable, refer to Troubleshooting, "Accelerator Pedal (Throttle) Position Sensor Circuit - Test".
Check the "Power train Data Link". Ensure that the SAE J1922 or the SAE J1939 Power train Data Link is not limiting the power.
Connect Cat ET to the data link connector.
Monitor the "Power train Data Link" status screen while the vehicle is experiencing problems.If the "Power train Data Link" status screen indicates that the "Power train Data Link" is limiting the power or the rpm, verify that the limit is not normal operation. If the limit is not normal operation, refer to the vehicle OEM for repairs.
Check the primary engine speed/timing sensor.If the signal from the primary engine speed/timing sensor is lost intermittently, the engine may misfire. The misfiring may occur when the signal source becomes the secondary engine speed/timing sensor. Ensure that the primary engine speed/timing sensor is properly installed. Also, ensure that the wiring is not damaged or pulled too tightly. Damaged wiring may cause an intermittent connection. Also, ensure that the crankshaft gear and the timing plate are not damaged. Refer to the following publication for additional information: Troubleshooting, "Engine Speed/Timing Sensor Circuit - Test"
Check the secondary engine speed/timing sensor.If the signal for the secondary engine speed/timing sensor is lost during engine start-up, additional time may be required to start the engine. The engine may also misfire during this time until the ECM determines the proper firing order. Refer to Troubleshooting, "Engine Speed/Timing Circuit - Test".


Back to top