353-66241-1 Nissan JOINT, SHIFT ROD


353-66241-1 JOINT, SHIFT ROD Nissan NS120A2, NS140A2, NS60C, NS70C, NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2 JOINT
353-66241-1 JOINT, SHIFT ROD Nissan
Rating:
18

Buy JOINT, SHIFT ROD 353-66241-1 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 51
 

Nissan entire parts catalog list:

NS120A2 2003,2004,2005
NS140A2 2003,2004,2005
NS60C 2003
NS70C 2003
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014
NSD70B 2003,2004,2005,2007,2008,2009
NSD70B 2006
NSD70B 2010
NSD75C2 2010,2011,2012,2013,2014
NSD90B 2003,2004,2005,2007,2008,2009
NSD90B 2006
NSD90B 2010
NSD90C2 2010,2011,2012,2013,2014

Information:

Connecting the J1939 Data Link
Table 1
Required Parts
Installation of a Single Module    
Part Number    Description    Qty    
5P-6001     Heat Shrink Tubing    
6 cm (2.4 inch)    
125-7876     Heat Shrink Tubing    
15 cm (6 inch)    
133-0969     Connector Socket (Extended)    2    
133-0970     Receptacle As (Tee)    1    
174-3016     Receptacle As (Termination Resistor)    1    
153-2707     Cable (Shielded Twisted Pair)     (1)    
165-0200     Cable As     2    
8T-8736 (2)     Connector Receptacle     1    
174-0503     Connecting Plug Kit (3)     1    
186-3736     Connector Socket     4    
( 1 ) Fabricated to length
( 2 ) The 8T-8736 Connector Receptacle for the service tool connector should only be used if one was not previously installed.
( 3 ) Use the blue wedge.
Table 2
Required Parts
Installation of Each Additional Module    
Part Number    Description    Qty    
5P-6001     Heat Shrink Tubing    
6 cm (2.4 inch)    
125-7876     Heat Shrink Tubing    
15 cm (6 inch)    
133-0969     Connector Socket (Extended)    2    
133-0970     Receptacle As (Tee)    1    
153-2707     Cable (Shielded Twisted Pair)     (1)    
165-0200     Cable As     1    
174-0503     Connecting Plug Kit (2)     2    
186-3736     Connector Socket     4    
( 1 ) Fabricated to length
( 2 ) Use the blue wedge.
Illustration 1 g00889188
Schematic for the J1939 Data LinkIllustration 1 shows the connection of modules to the J1939 data link. The following requirements must be met for installation of modules on the J1939 data link:
153-2707 Cable (Shielded Twisted Pair) must be used for all J1939 data link wiring. If the Caterpillar recommended cable is not used, the cable must meet J1939 standards.
Table 3
J1939 Specifications for Conductors    
    Minimum     Nominal     Maximum    
Impedance (ê)     108     120     132    
Specific pF/m     0     40     75    
Capacitance pF/m     0     70     110    
The total length of the data link must not exceed 40 m (130 ft).
All splices into the data link require a 133-0970 Receptacle As (Tee).
A 174-3016 Receptacle As (Termination Resistor) must be installed at the end of the data link in order to ensure proper operation.Note: A termination resistor for the J1939 data link is included in the Caterpillar supplied wiring harness to the customer connector. One additional termination resistor must be installed at the end of the data link.Use the following procedure to connect modules to the J1939 data link:
Illustration 2 g00889189
Connecting the customer connector to a tee
Illustration 3 g00779822
Connector sockets
Run the J1939 data link from the customer connector to a module.Note: The end of the data link must be within approximately 1 m (3.3 ft) of the module. The total length of the data link must not exceed 40 m (130 ft).
Run 153-2707 Cable (Shielded Twisted Pair) from the customer connector to the location of the first module. Cut the


Parts joint Nissan:

3C7-70220-1
 
3C7-70220-1 JOINT "A" ASSY IN
NS120A2, NS140A2, NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B
3C7-70224-1
 
3C7-70224-1 JOINT "A" ASSY OUT
NS120A2, NS140A2, NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS5BS, NS60C, NS70C, NS8B, NS9.8B, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B
3T7-09076-0
 
3T7-09076-0 JOINT, NIPPLE
NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
Back to top