3C7-60223-1 Nissan OIL SEAL, 22 - 42 - 7


3C7-60223-1 OIL SEAL, 22 - 42 - 7 Nissan NS120A2, NS140A2, NS60C, NS70C, NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2 OIL
3C7-60223-1 OIL SEAL, 22 - 42 - 7 Nissan
Rating:
43

Buy OIL SEAL, 22 - 42 - 7 3C7-60223-1 Nissan genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$13.23
 

07-04-2024
0.13[0.06] Pounds
US: Delmarva Marine
Tohatsu Oil Seal 3C7-60223-1
Tohatsu Genuine OEM Tohatsu
Number on catalog scheme: 9
 

Nissan entire parts catalog list:

NS120A2 2003,2004,2005
NS140A2 2003,2004,2005
NS60C 2003
NS70C 2003
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014
NSD70B 2003,2004,2005,2007,2008,2009
NSD70B 2006
NSD70B 2010
NSD75C2 2010,2011,2012,2013,2014
NSD90B 2003,2004,2005,2007,2008,2009
NSD90B 2006
NSD90B 2010
NSD90C2 2010,2011,2012,2013,2014

Information:


Illustration 1 g00530097
System Schematic For The Engine Speed SensorThe EMCP II+ monitors engine speed. The EMCP II+ uses engine speed in order to accomplish many tasks. These tasks are included in the following list.
Activating a shutdown for engine overspeed
Terminating engine cranking
Determining the oil step speed
Causing the air shutoff solenoid to engage during some fault shutdownsThe EMCP II+ does not control engine speed. The engine speed sensor is mounted on the flywheel housing of the engine.The sensor creates a sine wave signal. The signal is created from passing ring gear teeth. The rate of the signal is one pulse per tooth. The sensor sends the sine wave signal to the GSC+. The frequency of the signal is directly proportional to the speed of the engine.The GSC+ treats a CID 190 FMI 2 as a shutdown fault. The engine is not allowed to crank or the engine is not allowed to run when a CID 190 FMI 2 diagnostic code is active.Note: The Engine Speed Sensor is commonly referred to as magnetic pickup.Note: Engines that are equipped with an engine control module (ECM) or an Electronic Ignition System (EIS) have a separate speed sensor. The cable of the speed sensor that is used by the GSC is marked with one of the following numbers: 838-873, 838-973 and 973-938This troubleshooting procedure is for a CID 190 FMI 2 that is active or inactive.The possible causes of a CID 190 FMI 2 are listed below.
The frequency of the signal is beyond accepted limits. There is a short to the battery negative terminal.
The air gap of the speed sensor is too large.Clear the diagnostic code from the fault log after troubleshooting is complete.Test Step 1. CHECK THE HARNESS AND THE SPEED SENSOR.
Turn the engine control switch (ECS) to OFF/RESET.
Disconnect the harness connector from the GSC+.
At the GSC+ harness connector, measure the resistance from contact "1" to contact "2".Expected Result:The resistance should be from 100 to 350 ohms.Results:
OK - There is probably an intermittent problem. Proceed to Test Step 2.
NOT OK - The harness wiring or the speed sensor has failed. Proceed to Test Step 3.Test Step 2. CHECK FOR AN INTERMITTENT FAULT.
Turn


Parts oil Nissan:

332-60005-2
 
332-60005-2 OIL PLUG
NS120A2, NS140A2, NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS4C, NS50D2, NS5B, NS5BS, NS60C, NS70C, NS9.9D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B,
126-00121-0
 
126-00121-0 OIL SEAL, 30 - 45 - 8
NS25C3, NS30A4, NS40C, NS60C, NS70C
3C7-71030-0
 
3C7-71030-0 OIL FILTER ASS'Y
NS120A2, NS140A2, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3F3-71020-0
353-00121-0
3B7-00121-0
3C7-60223-0
99AA-2-0450
 
99AA-2-0450 OIL PIPE
NSD115A, NSD115A2
Back to top