3C7-67160-0 GROMMET, OIL PIPE Nissan
NS120A2, NS140A2, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B
GROMMET
Price: query
Rating:
Nissan entire parts catalog list:
- MOTOR COVER LOWER » 3C7-67160-0
- MOTOR COVER LOWER » 3C7-67160-0
- LOWER MOTOR COVER » 3C7-67160-0
- BOTTOM COWL (LOWER MOTOR COVER) » 3C7-67160-0
- LOWER MOTOR COVER » 3C7-67160-0
- LOWER MOTOR COVER » 3C7-67160-0
- BOTTOM COWL (LOWER MOTOR COVER) » 3C7-67160-0
- LOWER MOTOR COVER » 3C7-67160-0
Information:
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     237-9608     Mounting Bar     2    
B     376-8697     Guide Stud
5/8 - 11 by 36 inch
(1)     2    
8T-4122 Hard Washer     4    
6V-4803 Thrust Bearing     4    
4K-0367 Full Nut     8    
C     -     Loctite Graphite Anti-Seize     -    
D     -     Scotch Brite     1    
( 1 ) Cut 376-8697 guide studs to 18 inch lengths. Four 18 inch guide studs are required.Start By:
Remove the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Remove".Note: The following story is for 373-2561373-2563 Sea Water Heat Exchanger Gp .Note: The disassembly procedure can be performed while on the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hose assemblies and all plate assemblies for installation purposes. Plug all hose assemblies to prevent fluid loss, and to keep contaminants from entering the systems.
Illustration 1 g02127189
Disconnect hose assembly (1) and hose assembly (3) from front frame (2) .
Illustration 2 g02127190
Use suitable cribbing to place the heat exchanger in a flat position on the frame assembly. This position can help ensure proper alignment during the procedure.
Remove bolts (4) from the corners and the spacers. Install Tooling (B) . Apply Tooling (C) to the threads of the nut and the threads of the guide stud prior to installation. Install the thrust bearing, the hard washer, and the nuts on the guide stud. Ensure that Tooling (B) is securely installed. Place two nuts together and tighten the outer nut in order to install Tooling (B) . Position the thrust bearing, the hard washer, and one nut against the front frame.
Illustration 3 g02718824
Remove bolts (5) and the spacers. Install Tooling (A) .
Illustration 4 g02718823
Remove bolts (6) and bottom spacers (7) . Top spacers (7) will be removed after the front frame is loosened.
Illustration 5 g02128133
Loosen the nuts on Tooling (B) evenly. Ensure that Tooling (B) does not loosen from the frame assembly.Note: Do not loosen the nuts more than one turn per nut until the heat exchanger plates are no longer compressed.Note: As the front frame rises, the heat exchanger plates will slide along Tooling (A) .
Remove the top spacers from Step 5.
Remove Tooling (B) and Tooling (A) .
Illustration 6 g02128334
Note: Note the order and orientation of the heat exchanger plates and the seals during removal.
Remove front frame (2) , heat exchanger plates (8) , and the seals. Discard the sealsNote: A seal may stick to the front frame during removal.Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 7 g02718840
Parts grommet Nissan:
3B7-76093-0
3B7-76093-0 GROMMET, 25-5
NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B, NSF4C, NSF5C, NSF6C
3T5-04317-0
3T5-04317-0 GROMMET, CABLE TERMINAL
NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3T5-04319-0
3T5-04319-0 GROMMET, PIPE
NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3B7-61182-0
3B7-61182-0 GROMMET, EXHAUST HOUSING
NS120A2, NS140A2, NSD115A, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B
3B7-61207-0
3B7-61207-0 GROMMET, IDLE PORT
NS120A2, NS140A2, NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3C7-61212-0
3A3-84376-0
3A3-84376-0 GROMMET
NSD115A2, NSD40B2, NSD40B2, NSD50B2, NSD50B2, NSD70B, NSD75C2, NSD90B, NSD90C2, NSF15C, NSF20C, NSF25B, NSF25B, NSF30B, NSF4B, NSF5B, NSF6B, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
3T1-67005-0