3C8-76171-0 Nissan OVER-HEAT BUZZER


3C8-76171-0 OVER-HEAT BUZZER Nissan NS40D2, NS40D2, NS40D2, NS50D2, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15C, NSF20C, NSF25B, NSF25B, NSF30B, NSF8A3, N OVER
3C8-76171-0 OVER-HEAT BUZZER Nissan
Rating:
23

Buy OVER-HEAT BUZZER 3C8-76171-0 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Nissan entire parts catalog list:

NS40D2 2003
NS40D2 2004
NS40D2 2005
NS50D2 2003
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014
NSD70B 2003,2004,2005,2007,2008,2009
NSD70B 2006
NSD70B 2010
NSD75C2 2010,2011,2012,2013,2014
NSD90B 2003,2004,2005,2007,2008,2009
NSD90B 2006
NSD90B 2010
NSD90C2 2010,2011,2012,2013,2014
NSF15C 2010
NSF20C 2010
NSF25B 2010
NSF25B 2011,2012,2013,2014
NSF30B 2010
NSF8A3 2004,2007,2008,2009
NSF8A3 2010
NSF8A3 2011,2012,2013,2014
NSF9.8A3 2007,2008,2009
NSF9.8A3 2010
NSF9.8A3 2011,2012,2013,2014

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Drill Bit (3 mm) 1
B 1U-7600 Slide Hammer Puller 1
C 1U-7262 Telescopic Magnet 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the correct procedure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02873976
Typical example
Apply clean grease to Tooling (A) in order to prevent any swarf that is generated from entering the engine. Use Tooling (A) to drill three evenly spaced holes in crankshaft rear seal (4).
Use Tooling (B) with care in order to remove crankshaft rear seal (4) from flywheel housing (1). Alternate the position of Tooling (B) from one hole to another. Alternating the position of Tooling (B) will allow the crankshaft rear seal to be easily removed from the flywheel housing.
Apply clean grease to Tooling (A) in order to prevent any swarf that is generated from entering the engine. Use Tooling (A) to drill two evenly spaced holes in crankshaft wear sleeve (3).
Use Tooling (B) with care in order to remove crankshaft wear sleeve (3) from crankshaft (2). Alternate the position of Tooling (B) from one hole to the other. Alternating the position of Tooling (B) will allow the crankshaft wear sleeve to be easily removed from the crankshaft.
Use Tooling (C) to collect any swarf that is on the flywheel housing or crankshaft assembly. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
D 390-1124 Crankshaft Rear Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flange of the crankshaft and the inside of the flywheel housing are clean and free from oil and damage.
Illustration 2 g02876556
Typical example
Illustration 3 g02876596
Sectional view of the crankshaft rear seal, the crankshaft, and the installation tool
Crankshaft rear seal (4) and crankshaft wear sleeve (3) are supplied as a crankshaft rear seal assembly (5) and should not be separated for installation. Note: Do not remove the crankshaft rear seal from the crankshaft wear sleeve.
Use Tooling (D) and follow Step 3.a through Step 3.f in order to install crankshaft rear seal assembly (5).
Position the adaptor of Tooling (D) onto the palm of the crankshaft and secure with bolts.
Position the new crankshaft rear seal assembly (5) over the adaptor onto the rear of the crankshaft.
Align the seal installer of Tooling (D) with the crankshaft. Note: Check that the installer of Tooling (D) is parallel to the adaptor.
Install the nut and washer to the locator.
Tighten the nut until the installer bottoms out on the adaptor in order to install crankshaft rear seal assembly (5) into flywheel housing (1) and onto crankshaft (2).
Remove Tooling (D). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".


Parts over Nissan:

3C8-76172-0
 
3C8-76172-0 OVER-HEAT SENSOR
NS40D2, NS40D2, NS40D2, NS50D2
3A3-76171-0
 
3A3-76171-0 OVER-HEAT BUZZER
NS120A2, NS140A2, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD50A
Back to top