3C8-62475-0 Nissan PIN

Cross-Reference Information for Event Codes
Event codes are generated when abnormal operating conditions exist. Table 1 is a list of the event codes for the engine. The event codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Table 1
J1939 Code and Description Troubleshooting Procedure
168-17
Battery Potential / Power Input #1 : Low - least severe (1) Troubleshooting, "Electrical Power Supply - Test"
1664-31
Engine Automatic Start Failed Troubleshooting, "Engine Cranks but Does Not Start"
3029-31
Engine start inhibited, pre-lube system issue Troubleshooting, "Prelubrication Pump Problem"
3551-1
Engine Oil Priming State : Low - most severe (3) Troubleshooting, "Oil Pressure Is Low"
3551-17
Engine Oil Priming State : Low - least severe (1) Troubleshooting, "Prelubrication Pump Problem"
3551-31
Engine Oil Priming State Troubleshooting, "Prelubrication Pump Problem"
4082-31
Fuel Pump Primer Control Troubleshooting, "Fuel Pressure Is Low"
5578-14
Engine Fuel Delivery Absolute Pressure Troubleshooting, "Fuel Pressure Is Low"
7902-17
Starting/Lighting/Ignition (SLI) Battery Pack #1 Battery #1 Voltage : Low - least severe (1) Troubleshooting, "Electric Power Supply - Test" Parts of the Event Code
Event Code - The E identifies the code as an event code. The XXX(X) is a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. The code is followed by a description of the code. Refer to the following example:
E360(1) Low Oil Pressure
E360(2) Low Oil Pressure
E360(3) Low Oil PressureThe definition for the levels of severity for an event are defined below:
Table 2
Indicators (1), (2), and (3)
Warning Category Indicator Severity
(1) Least Severe
(2) Moderate Severity
(3) Most Severe Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g06079642
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes.Logged Event Codes
When the ECM generates an event code, the ECM may log the event code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
To troubleshoot the engine, perform the following steps to diagnose a malfunction:
Obtain the following information about the complaint:
The event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.
Determine whether any additional events occurred.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
ConnectorsBe sure to check the connectors. This check is important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code.Parameter Settings of the Engine Monitoring System
The default settings for the parameters are programmed at the factory. The parameter settings for the engine monitoring system can also be viewed on Cat® Electronic Technician (ET).