3C8-76015-0 Nissan PINION


3C8-76015-0 PINION Nissan NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF20C, NSF20C, NSF25A, NSF25B, NSF25B, NSF25B, NSF30A, NSF30B, NSF3 PINION
3C8-76015-0 PINION Nissan
Rating:
68

Buy PINION 3C8-76015-0 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 1-1
 

Nissan entire parts catalog list:

NS40D2 2003
NS40D2 2004
NS40D2 2005
NS50D2 2003
NS60C 2003
NS70C 2003
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014
NSF15B2 2003,2004,2005,2007,2008
NSF15B2 2006
NSF15C 2008,2009,2011,2012,2013,2014
NSF15C 2010
NSF18B2 2003,2004,2005,2007,2008
NSF18B2 2006
NSF20C 2008,2009,2011,2012,2013,2014
NSF20C 2010
NSF25A 2003,2004,2005
NSF25B 2005,2006,2007,2008,2009
NSF25B 2010
NSF25B 2011,2012,2013,2014
NSF30A 2003,2004,2005
NSF30B 2005,2006,2007,2008,2009,2011,2012,2013,2014
NSF30B 2010
NSF9.9B2 2003,2004
NSF9.9B2 2006
NSF9.9C 2008

Information:

(ET)".
Start the WinFlash PC Program.
Ensure that the ignition key switch is ON and ensure that the engine is off.
Select the part number of the engine personality module that needs to be programmed into the ECM. Program the personality module. A new ECM is shipped with a blank personality module.Note: The WinFlash PC Program provides the part number of the selected file for the ECM, the application and the software. Ensure that this file matches the engine before you begin to flash the file into the ECM.
Messages from the personality module and the meaning of the messagesA new ECM comes with a blank personality module. A blank personality module has not been programmed. A blank personality module will prompt you for all three of the following messages. The information that is contained in the ECM Status will be scrambled if the module has not been programmed previously. This is normal.
Message The engine ID in the flash file does not match the engine ID in the ECM.
Meaning The ECM has a personality module for a different engine.
Solution Stop the transfer of files. Access information about the ECM status under the menu for the ECM. Ensure that the file that was being transferred matches the engine application.
Message The application ID in the flash file does not match the application ID in the ECM.
Meaning The ECM has a personality module for a different application. For example, the ECM has a personality module for a 3126B HEUI On-Highway truck engine and you are attempting to program a personality module for a 3508B Marine engine.
Solution Stop the transfer of files. Access information about the ECM status under the menu for the ECM. Ensure that the file that was being transferred is for a personality module for an On-Highway truck.
Message The ID of the ECM in the flash file does not match the ID of the ECM in the ECM.
Meaning The ECM is not for use with an On-Highway truck application.
Solution Stop the transfer of files. Access information about the ECM Status under the menu for the ECM. Ensure that the ECM on the engine is for an On-Highway truck application.Note: The amount of time that is required to flash a personality module is significantly longer than earlier applications. The amount of time that is required to flash a personality module with a 7X-1700 Communication Adapter is approximately ten minutes or more. The amount of time that is required to flash a personality module with a MPSI Pro-link with the Caterpillar cartridge as a communications adapter is approximately 20 minutes or more.Note: If you access the ECM status under the menu for the ECM, but you do not program the personality module, complete the following procedure. Before using the ET, turn the vehicle's ignition keyswitch to the OFF position, and then turn the vehicle's ignition keyswitch to the ON position. If the ignition keyswitch is not cycled after reading the ECM Status, the ECM will not communicate with your service tool or the ECM will not start. Cycling the ignition keyswitch is not necessary after the personality module has been programmed by using the WinFlash PC Program.
Start the engine and check for proper operation.
Program any parameters that were not previously in the old personality module if a 253-02 Check Customer Or System Parameters (56) diagnostic code is active. Read the diagnostic code from the ET Active Diagnostic Code screen in order to determine the parameter (parameters) that requires programming.
On initial powerup of a new ECM, six parameters must be programmed to avoid a 253-02 Check Customer Or System Parameters (56) Diagnostic Code: Full Load Setting (FLS), Full Torque Setting (FTS), Vehicle Speed Calibration (ppm), Rating Number, Engine Serial Number and Injector Trim Codes. Refer to Troubleshooting, "Programming Parameters".


Back to top