3B7-72662-0 Nissan PLATE, FITTING


3B7-72662-0 PLATE, FITTING Nissan NS120A2, NS140A2, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2 PLATE
3B7-72662-0 PLATE, FITTING Nissan
Rating:
58

Buy PLATE, FITTING 3B7-72662-0 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 3-4
 

Nissan entire parts catalog list:

NS120A2 2003,2004,2005
NS140A2 2003,2004,2005
NS40C 2004
NS40D2 2003
NS40D2 2004
NS40D2 2005
NS50D2 2003
NS60C 2003
NS70C 2003
NSD115A 2006,2007,2008,2009,2010
NSD115A2 2010,2011,2012,2013,2014
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014
NSD70B 2003,2004,2005,2007,2008,2009
NSD70B 2006
NSD70B 2010
NSD75C2 2010,2011,2012,2013,2014
NSD90B 2003,2004,2005,2007,2008,2009
NSD90B 2006
NSD90B 2010
NSD90C2 2010,2011,2012,2013,2014

Information:


Table 1
Diagnostic Trouble Codes
CDL Code J1939 Code Code Description
(code descriptions may vary) Comments
E1045 (3) 102-1 Engine Intake Manifold #1 Pressure : Low - most severe (3) The code is logged.
Engine power is derated.
E1045 (2) 102-18 Engine Intake Manifold #1 Pressure : Low - moderate severity (2) The code is logged.
Engine power is derated.
E1107 (3) 2630-1 Engine Charge Air Cooler Outlet Temperature : Low - most severe (3) The code is logged due to a restriction in the intake manifold that can be causes by icing.
Follow the troubleshooting procedure in order to identify the root cause of the problem.
Table 2
Associated Diagnostic Trouble Codes
E583
107-15
107-16
Table 3
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Connect to Caterpillar Electronic Technician (ET).
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Determine if an associated code listed in Table 2 is active or logged. Table 2 lists associated diagnostic codes.
Codes
Result: An associated code is active.
Refer to Troubleshooting, "Diagnostic Trouble Codes" in order to troubleshoot the associated diagnostic code.
Result: An associated code is not active or logged.
Proceed to Test Step 2.
Result: An E1045 or 102-18 code is active.
Proceed to Test Step 2.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. Check the Air Inlet System for Restrictions
A. Visually inspect the air filter for cleanliness on engines without an electronic monitoring system on the inlet air system. A mechanical indicator may be used to monitor inlet air restrictions. Use the indicator to determine the cleanliness of the inlet air system. Also, inspect the piping for restrictions.
Restrictions
Result: The air filter is clean and a restriction is not found.
Proceed to Test Step 3.
Result: The inlet air system is restricted.
Clean the filter or replace the filter. Remove all obstructions in the inlet air piping. Verify that the problem has been resolved. If the problem still exists, proceed to Test Step 3.
Illustration 1 g02023778
Typical points of inspection
Table 4
Troubleshooting Test Steps Values Results
3. Inspect the Air Piping and Connections
A. Inspect the piping and the hose connections from the turbocharger compressor outlet to the Air to Air Aftercooler (ATAAC) inlet ( if equipped). Remove the hose connections and inspect the hose connections for cuts or damage.
Connections
Result: The piping or hose connections were damaged.
Replace the damaged piping or hose connections. Verify that the problem has been resolved.
If the problem still exists, proceed to Test Step 4.
Result: The piping was not damaged.
Proceed to Test Step 4.
4. Perform an ARD Air System Service Test
A. Perform the ARD Air System Service Test in Cat ET. The test will verify that the ARD air valve is working properly.
ARD Air Service Test
Result: The ARD Air System Service Test did not complete successfully.
Replace the ARD air valve. Verify that the problem has been resolved. Perform the ARD Air System Service Test.
Return the engine to service if the test was successful. If the test was not successful, proceed to Test Step 5.
Result: The ARD Air System Service Test did complete successfully.
Proceed to Test Step 5.
5. Inspect the Turbocharger
A. Remove the connection for the inlet air and the exhaust connection to the turbocharger. Verify that the compressor wheel and the turbine wheel are spinning freely. Verify that the compressor wheel and the turbine wheel are not damaged.
Turbocharger
Result: The turbocharger wheels are damaged.
Replace the turbocharger. Return the unit to service.
Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts plate Nissan:

3C8-66116-0
 
3C8-66116-0 PLATE, SHIFT LEVER STOPPER
NS40D2, NS40D2, NS40D2, NS50D2, NS8B, NS9.8B, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSF15B2, NSF15B2, NSF18B2, NSF18B2, NSF25A, NSF25B, NSF25B, NSF25B, NSF30A, NSF30B, NSF30B, NSF8A, NSF8A2, NSF8A3, NSF9.
3A0-06322-0
 
3A0-06322-0 PLATE, ELECTRIC
NS25C3, NS30A4, NS40C
345-05134-0
 
345-05134-0 PLATE, ROPE ANCHOR
NS25C3, NS30A4, NS40C
3B7-72665-0
 
3B7-72665-0 PLATE, FITTING
NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD40A, NSD40B, NSD50A, NSD50B, NSD70B, NSD70B, NSD70B, NSD90B, NSD90B, NSD90B
3C8-71035-0
 
3C8-71035-0 PLATE, FUEL FILTER
NS40D2, NS40D2, NS40D2, NS50D2
3B7-60012-1
 
3B7-60012-1 PLATE, GEAR CASE
NS120A2, NS140A2, NS60C, NS70C, NSD115A, NSD115A2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2
3F3-06072-1
353-66327-0
Back to top