920803-0518 Nissan SCREW


920803-0518 SCREW Nissan NS4C, NS5B, NS5BS, NS8B, NS9.8B, NSF4A2, NSF4B, NSF4C, NSF5A2, NSF5B, NSF5C, NSF6A2, NSF6B, NSF6C, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3 SCREW
920803-0518 SCREW Nissan
Rating:
78

Buy SCREW 920803-0518 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Nissan entire parts catalog list:

NS4C 2003
NS5B 2003
NS5BS 2003
NS8B 2003
NS9.8B 2003
NSF4A2 2003,2004,2005
NSF4B 2010
NSF4C 2011,2012,2013,2014
NSF5A2 2003,2004,2005
NSF5B 2010
NSF5C 2011,2012,2013,2014
NSF6A2 2003,2004,2005
NSF6B 2010
NSF6C 2011,2012,2013,2014
NSF8A3 2004,2007,2008,2009
NSF8A3 2010
NSF8A3 2011,2012,2013,2014
NSF9.8A3 2007,2008,2009
NSF9.8A3 2010
NSF9.8A3 2011,2012,2013,2014

Information:


Illustration 1 g00882677
(Y) "ADD" mark. (X) "FULL" mark. (Z) "Effective Length".
(Z-LH Service Engines) 642 mm (25.3 inch)
(Z-RH Service Engines) 479 mm (18.9 inch) The engine is shipped with an engine oil level gauge that is not marked. The engine oil level gauge is not marked because the angle of the installation and the side for servicing the engine oil can be different for each engine. The angle of the installation and the side for servicing the engine oil will affect "ADD" mark (Y) and "FULL" mark (X) that is engraved on the engine oil level gauge.The engine oil level gauge should be calibrated after the engine is installed in the vessel. Use the following procedure in order to verify that "ADD" mark (Y) is correct. Use the following procedure in order to establish actual "FULL" mark (X) on the engine oil level gauge. Refer to table 1 and table 2 in order to determine the location for the "ADD" and "FULL" marks for a particular installation.
Refer to the Operation and Maintenance Manual for more information on lubricant specifications.
Operate the engine until normal operating temperature is achieved. Stop the engine. Remove one of the drain plugs for the engine crankcase. Allow the engine oil to drain.
Remove the used engine oil filter. Install the new engine oil filter. Install the drain plug for the engine crankcase. Tighten the drain plug for the engine crankcase to 70 14 N m (50 10 lb ft). Note: The engine may be equipped with auxiliary engine oil filters. Volumes that are different from the standard amounts may be required. Refer to the OEM specifications.
Pour 20.8 L (22 qt) of engine oil into the engine crankcase. Allow enough time for the engine oil to drain into the engine crankcase. Approximately 20 minutes should be allowed. Check the engine oil level. Wait for a few minutes. Check the engine oil level again. Proceed after the engine oil level stops changing.
Mark the engine oil level on the engine oil level gauge. Use a marking pen in order to engrave "ADD" mark (Y).
Pour 3.8 L (4 qt) of engine oil into the engine crankcase. Allow enough time for the engine oil to drain into the engine crankcase.
Mark the engine oil level on the engine oil level gauge. Use a marking pen in order to engrave "FULL" mark (X).
Start the engine. Ensure that the lubrication system is filled. Inspect the lubrication system for leaks.
Stop the engine and allow enough time for the engine oil to drain into the engine crankcase.
Check the engine oil level on the engine oil level gauge. If the engine oil level is not at calibrated "FULL" mark (X), fill the sump to the calibrated "FULL" mark. Record the amount of oil that is added. This additional engine oil is the system capacity plus the engine oil in the sump. This additional engine oil is the amount of engine oil that is required when the engine oil is changed. Record the engine oil capacity for the system for future changes of the engine oil. 3176C and 3196 Marine Engine Dipstick MarkingsNote: Use the following tables if these conditions exist:
The engine is installed with a 0 degree slant angle.
No auxiliary engine oil filters are used on the engine.
Table 1
3176C and 3196 Marine Engine
Oil Gauge Markings (mm)
LH Service (1)
Tilt Angle(2) LH Service
"ADD" Mark
Y LH Service
"FULL" Mark
X
-15° 120 mm (4.7 inch) 133 mm (5.2 inch)
-13° 113 mm (4.4 inch) 125 mm (4.9 inch)
-11° 110 mm (4.3 inch) 124 mm (4.9 inch)
-9° 106 mm (4.2 inch) 118 mm (4.6 inch)
-7° 100 mm (3.9 inch) 110 mm (4.3 inch)
-5° 93 mm (3.7 inch) 106 mm (4.2 inch)
-3° 87 mm (3.4 inch) 99 mm (3.9 inch)
-1° 82 mm (3.2 inch) 93 mm (3.7 inch)
0° 79 mm (3.1 inch) 89 mm (3.5 inch)
1° 73 mm (2.9 inch) 85 mm (3.3 inch)
3° 68 mm (2.7 inch) 81 mm (3.2 inch)
5° 63 mm (2.5 inch) 74 mm (2.9 inch)
7° 54 mm (2.1 inch) 67 mm (2.6 inch)
9° 47 mm (1.9 inch) 61 mm (2.4 inch)
11° 38 mm (1.5 inch) 52 mm (2.0 inch)
13° 30 mm (1.2 inch) 43 mm (1.7 inch)
15° 19 mm (0.7 inch) 36 mm (1.4 inch)
(1) (Z-LH Service Engines) 642 mm (25.3 inch).
(2) The tilt angles in this chart are the engine installation angles for the vessel. A positive angle indicates that the front of the engine is raised.
Table 2
3176C and 3196 Marine Engine
Oil Gauge Markings (mm)
RH Service (1)
Tilt Angle(2) RH Service
"ADD" Mark
Y RH Service
"FULL" Mark
X


Parts screw Nissan:

921521-6520
 
921521-6520 SCREW
NS2.5A2, NS3.5A2, NS3.5B2, NS4C, NS5B, NS5BS, NS8B, NS9.8B, NSF4A2, NSF4B, NSF4B, NSF5A2, NSF5B, NSF5B, NSF6A2, NSF6B, NSF6B
921503-0612
 
921503-0612 SCREW
NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS4C, NS5B, NS5BS, NS8B, NS9.8B, NSF2.5B, NSF2.5B, NSF2B, NSF3.5B, NSF3.5B, NSF4A2, NSF4B, NSF4B, NSF5A2, NSF5B, NSF5B, NSF6A2, NSF6B, NSF6B, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
921503-6410
 
921503-6410 SCREW
NS4C, NS5B, NSF25B, NSF25B, NSF30B
921803-0620
 
921803-0620 SCREW
NS4C, NS5B, NS5BS, NSF15B2, NSF18B2, NSF4A2, NSF4B, NSF4B, NSF4C, NSF5A2, NSF5B, NSF5B, NSF5C, NSF6A2, NSF6B, NSF6B, NSF6C, NSF9.9B2
921521-6625
 
921521-6625 SCREW
NS8B, NS9.8B
3F3-03234-0
 
3F3-03234-0 SCREW
NS120A2, NS140A2, NS25C3, NS30A4, NS60C, NS70C, NS8B, NS9.8B
921503-0408
 
921503-0408 SCREW
NS40C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF15C, NSF15C, NSF20C, NSF20C, NSF25B, NSF25B, NSF30B, NSF8A3, NSF8A3, NS
921603-0512
 
921603-0512 SCREW
NS60C, NS70C, NSD115A2, NSD40B2, NSD40B2, NSD50B2, NSD50B2, NSD70B, NSD75C2, NSD90B, NSD90C2, NSF15C, NSF20C, NSF25B, NSF25B, NSF30B, NSF4B, NSF5B, NSF6B, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
Back to top