921521-0616 Nissan SCREW


921521-0616 SCREW Nissan NS25C3, NS30A4 SCREW
921521-0616 SCREW Nissan
Rating:
43

Buy SCREW 921521-0616 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

NS25C3   NS30A4   Nissan

Nissan entire parts catalog list:

NS25C3 2003,2005
NS30A4 2003

Information:


Illustration 1 g00293085
Fuel injection nozzle (1) Tighten the union nut of the high pressure fuel line (not shown) to the following torque. ... 22 N m (16 lb ft) (2) Tighten the banjo bolts of the leak off tubing (not shown) to the following torque. ... 9.0 N m (80 lb in) (3) Tighten the nut of the fuel injection nozzle to the following torque. ... 30 N m (22 lb ft)Note: When the fuel injection nozzle is installed, put a 2.0 mm (0.08 inch) bead of 4C-5591 Anti-Seize Compound on the first two threads of the union nut. (4) Wire clip (5) Seat washerNote: Remove the original seat washer from the threaded hole for the fuel injection nozzle which is located in the cylinder head. If the original seat washer is not removed, the projection of the nozzle will be incorrect when a new seat washer is installed. Do not reuse the seat washer (5) .Bench test the fuel injection nozzles at a temperature of 18 to 20 °C (64 to 70 °F).Note: Use clean SAE J-967 oil (ISO 4113) when you are conducting the test. The oil is available in 5 gallon containers ( 6V-6068 Calibration Fluid ) and 55 gallon containers ( 6V-6067 Calibration Fluid ). If dirty oil is used for the test, the components of the fuel injection nozzle will be damaged.Refer to Testing And Adjusting, "Fuel Injection Nozzle - Test".
Table 1
Service Setting For The Fuel Injection Nozzle    
Engine Model     Code (1)     Minimum and Maximum Pressure    
3054     KN    
29392 kPa (4263 psi)    
3054B     KW    
29392 kPa (4263 psi)    
( 1 ) The code letters are stamped on the side of the fuel injector body. The code letters are located below the connection for the nut of the high pressure fuel line.Note: Ensure that the new fuel injection nozzles have the same identification code as the nozzles which were originally installed in the cylinder head.Leakage in 10 seconds ... 0 drops 3056 Engine
Illustration 2 g00755990
(1) Bolt Tighten the two bolts to the following torque. ... 12 N m (9 lb ft) (2) Clamp (3) Seat washerRemove the original seat washer from the threaded hole for the fuel injection nozzle which is located in the cylinder head. If the original seat washer is not removed, the projection of the nozzle will be incorrect when a new seat washer is installed. Do not reuse seat washer (3) .Bench test the fuel injection nozzles at the following temperature. ... 18° to 20°C (64° to 70°F)
Do not use dirty test fluids when you test fuel injection nozzles. Also, do not test fuel injection nozzles unless you have the correct service tools.The use of dirty test fluids and the use of incorrect service tools will result in damage to fuel injection nozzles.
Caterpillar Inc. recommends the use of SAEJ-967 Calibration Oil (ISO 4113) for testing the fuel injection nozzles. The oil is available in 5 gallon containers ( 6V-6068 Calibration Fluid ) and 55 gallon containers ( 6V-6067 Calibration Fluid ).Refer to the Testing and Adjusting Module, "Fuel System" topic for additional information.
Table 2
Service Setting For The Fuel Injection Nozzle    
Engine Model     Code (1)     Minimum and Maximum Pressure    
3056 Naturally Aspirated     NP    
22298 kPa (3234 psi)    
3056 Turbocharged     RS    
25338 kPa (3675 psi)    
( 1 ) The code letters are stamped on the side of the fuel injector body. The code letters are located below the connection for the nut of the high pressure fuel line.
Ensure that the new fuel injection nozzles have the same identification code as the previous fuel injection nozzles in the cylinder head. If the fuel injection nozzles have an incorrect identification code, damage to the engine may occur.
Leakage in 10 seconds ... 0 drops


Parts screw Nissan:

921503-0612
 
921503-0612 SCREW
NS2.5A2, NS25C3, NS3.5A2, NS3.5B2, NS30A4, NS4C, NS5B, NS5BS, NS8B, NS9.8B, NSF2.5B, NSF2.5B, NSF2B, NSF3.5B, NSF3.5B, NSF4A2, NSF4B, NSF4B, NSF5A2, NSF5B, NSF5B, NSF6A2, NSF6B, NSF6B, NSF8A3, NSF8A3, NSF8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
3F3-03234-0
 
3F3-03234-0 SCREW
NS120A2, NS140A2, NS25C3, NS30A4, NS60C, NS70C, NS8B, NS9.8B
922503-6414
 
922503-6414 SCREW
NS120A2, NS140A2, NS25C3, NS30A4, NS60C, NS70C, NS8B, NS9.8B, NSF15B2, NSF15B2, NSF18B2, NSF18B2, NSF25A, NSF30A, NSF9.9B2, NSF9.9B2
921503-0525
 
921503-0525 SCREW
NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS8B, NS9.8B, NS9.9D2, NSF4B, NSF4B, NSF4C, NSF5B, NSF5B, NSF5C, NSF6B, NSF6B, NSF6C
921503-6408
 
921503-6408 SCREW
NS15D2, NS18E2, NS25C3, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS8B, NS9.8B, NS9.9D2, NSF8A, NSF8A2, NSF8A3, NSF8A3, NSF8A3, NSF8A3, NSF9.8A, NSF9.8A2, NSF9.8A3, NSF9.8A3, NSF9.8A3, NSF9.8A3
921506-0525
 
921506-0525 SCREW
NS15D2, NS18E2, NS25C3, NS30A4, NS9.9D2
922503-6510
 
922503-6510 SCREW
NS25C3, NS30A4, NS40C
921521-0610
 
921521-0610 SCREW
NS25C3, NS30A4
Back to top