951503-0215 Nissan SPLIT PIN, 2-15


951503-0215 SPLIT PIN, 2-15 Nissan NS40D2, NS40D2, NS40D2, NS50D2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2 SPLIT
951503-0215 SPLIT PIN, 2-15 Nissan
Rating:
38

Buy SPLIT PIN, 2-15 951503-0215 Nissan genuine, new aftermarket parts with delivery
Number on catalog scheme: 2-4
 

Nissan entire parts catalog list:

NS40D2 2003
NS40D2 2004
NS40D2 2005
NS50D2 2003
NSD40A 2003
NSD40B 2003,2004,2005,2007,2008,2009,2010,2011
NSD40B 2006
NSD40B2 2010
NSD40B2 2011,2012,2013,2014
NSD50A 2003
NSD50B 2003,2004,2005,2007,2008,2009,2010
NSD50B 2006
NSD50B2 2010
NSD50B2 2011,2012,2013,2014

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01340605
Typical example
If necessary, remove the assembly of dipstick tube. Loosen nut (1) and remove tube assembly (2). remove seal (3) from the tube assembly.Note: Identify the position and orientation of the tube assembly.
Illustration 2 g01340606
Typical example
Place a suitable container below engine oil pan (7). Remove drain plug (5) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Remove O-ring seal (6) from drain plug (5) .
Disconnect breather hose from the clip that secures the hose to the engine oil pan. Position the breather hose away from the engine oil pan.
Support the assembly of the engine oil pan. Loosen the long isolating screws (8) and the two short isolating screws (9). Mark the position of the clip that secures breather hose. Remove the clip.Note: The isolating screws are held captive by joint (4) .
Remove the assembly of the engine oil pan from the engine.
If necessary, remove the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Guide Stud
(M8 by 100 mm)     4    
B     6V-6640     Sealant     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If necessary, install the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Illustration 3 g01340664
Typical Example
Install Tooling (A) to positions (X) in the cylinder block.
Illustration 4 g01340606
Typical example
Ensure that the engine oil pan (7) is clean and free from damage. Clean the isolating screws (8) and (9). Inspect the isolating screws for deterioration or damage. If necessary, replace the isolating screws. If necessary, ensure that the mating surface of the isolating frame is clean.Note: The isolating screws must be replaced as a complete set in order to ensure the correct clamping of the engine oil pan.
Position a new joint (4) onto the engine oil pan (7) .
Install the isolating screws (8) and (9) to the engine oil pan. Do not install the isolating screws (8) in positions (X). Refer to Illustration 3.Note: The isolating screws are held captive by the joint.
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the isolating frame (12). Install the clip that secures the breather hose in the correct position.
Illustration 5 g01340724
(X) Position of guide studs. (Z) Position of short isolating screws.
Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 5.
Remove Tooling (A) .
Illustration 6


Parts split Nissan:

951503-0212
 
951503-0212 SPLIT PIN, 2 - 12
NS15D2, NS18E2, NS25C3, NS3.5B2, NS30A4, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NS9.9D2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSF15B2, NSF15B2, NSF15C, NSF15C, NSF18B2, NSF18B2, NSF2.5A, NS
951503-0325
 
951503-0325 SPLIT PIN, 3-25
NS120A2, NS140A2, NS40C, NS40D2, NS40D2, NS40D2, NS50D2, NS60C, NS70C, NSD115A, NSD115A2, NSD40A, NSD40B, NSD40B, NSD40B2, NSD40B2, NSD50A, NSD50B, NSD50B, NSD50B2, NSD50B2, NSD70B, NSD70B, NSD70B, NSD75C2, NSD90B, NSD90B, NSD90B, NSD90C2, NSF50B, NS
951503-1520
 
951503-1520 SPLIT PIN
NS40D2, NS40D2, NS40D2, NS50D2
Back to top