3R0-65100-0 Nissan WATER PIPE, S

Illustration 1 g00792738
Indicator lamp for the engineThe indicator lamp indicates when the engine is running.The lamp operates on 24 volts. The lamp has a green lens that displays "ENGINE RUN". Use the lamp test switch in order to test the lamp.The lamp is connected to the circuit of the run relay. The lamp will illuminate when the engine is running. The lamp shuts off when the shutdown circuit is active.Indicator Lamp (Engine Prelubrication)
Illustration 2 g00792738
Indicator lamp for engine prelubricationThe lamp indicates the prelubrication of the engine.The lamp operates on 24 volts. The lamp has a green lens that displays "ENGINE PRELUBE".The lamp is connected to the circuit of the "starting oil" relay. The lamp indicates that the engine has oil for starting. The lamp will illuminate when the lubrication of the engine exceeds 9 3 kPa (1.3 0.4 psi) for intermittent prelube systems. The lamp will illuminate when the lubrication of the engine is detected for continuous prelube systems. The lamp shuts off when the engine is running.Indicator Lamp (Alarm)
Illustration 3 g00792739
Indicator lamps for alarmsThe alarm lamps are available on the annunciator panel only. There are 16 indicators that are available for the different systems. The lamp indicates the alarm that is active.The lamps operate on 24 volts. The lamps are activated by outputs from the programmable logic controller. The lamps have amber lenses that display one of the following alarms.
Engine speed pickup
Low engine oil level
Low engine oil pressure
Particle detection
High engine oil temperature
High jacket water coolant temperature
Low jacket water coolant level
Tripped breaker
High manifold air temperature
High exhaust manifold temperature
Low starting air pressure
High fuel temperature
Low fuel pressure
Low jacket water pressure
Low aftercooler/oil cooler water pressure
Spare Use the lamp test switch in order to test the lamps.The lamp is connected to the particular alarm circuit. The lamps indicate that an alarm condition is present. When an alarm condition is present, the indicator will flash. The lamp will flash until the alarm is acknowledged. After the alarm is acknowledged, the lamp will stay on. The lamp will stay on until the alarm condition has been cleared and the reset button has been depressed.ReferenceSee Systems Operation, "Alarm Mode" for more information.Indicator Lamp (Shutdowns)
Illustration 4 g00792740
Indicator lamps for shutdownsThe shutdown lamps are available on the annunciator panel only. There are 8 indicators that are available for the different systems. The lamp indicates the shutdowns that are active.The lamps operate on 24 volts. The lamps are activated by outputs from the programmable logic controller. The lamps have red lenses that display one of the following alarms.
Engine overspeed
High crankcase pressure
Low engine oil pressure
Particle detection
High engine oil temperature
High jacket water coolant temperature
Low jacket water coolant level
Spare Use the lamp test switch in order to test the lamps.The lamp is connected to the particular shutdown circuit. The lamps indicate that a shutdown condition is present. When a shutdown condition is present, the indicator will flash. The lamp will flash until the shutdown is acknowledged. After the shutdown is acknowledged, the lamp will stay on. The lamp will stay on until the shutdown condition has been cleared and the reset button has been depressed.ReferenceSee Systems Operation, "Shutdown Mode" for more information.Indicator Lamp (Programmable Logic Controller)
Illustration 5 g00792738
Indicator lamp for programmable logic controllerThe indicator lamp for the programmable logic controller (PLC) is available on the annunciator panel only. The lamp indicates that the programmable logic controller is operating.The lamps operate on 24 volts. The lamp has a green lens that displays "PLC RUN". Use the lamp test switch in order to test the lamp.The lamp is connected to an output of the PLC. The lamp will be illuminated whenever the PLC is executing the program for the annunciator panel. The lamp will be off if the controller is not in the run mode or the controller has a major fault.Note: When the lamp is not on, the annunciator panel may not be working.ReferenceSee Systems Operation, "Programmable Logic Controller" for more information.