67214-95600 Suzuki Actuator


67214-95600 Actuator Suzuki 30ELE, 30ESE, 30MLE, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DT115, DT140, DT150, DT15C, DT200, DT20ELG, DT20ELH, DT20ELJ, DT20 Actuator
67214-95600 Actuator Suzuki
Rating:
58

Buy Actuator 67214-95600 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Suzuki entire parts catalog list:

30ELE 1984
30ESE 1984
30MLE 1984
DF25 2000,2001,2002,2003,2004,2005
DF25Q 2000,2001,2002,2003,2004,2005,2006,2007
DF25Q(QR) 2000,2001,2002,2003,2004,2005,2006,2007
DF25T 2000,2001,2002,2003,2004,2005,2006,2007
DF30 2000,2001,2002,2003,2004,2005,2006
DF30Q 2000,2001,2002,2003,2004,2005,2006,2007
DF30Q(QR) 2000,2001,2002,2003,2004,2005,2006,2007
DF30T 2000,2001,2002,2003,2004,2005,2006,2007
DF40 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF40 2010
DF40QH 1999,2000,2001,2002,2003,2004,2005,2006,2007
DF40TL 1999,2000,2001,2002,2003,2004,2005,2006,2007
DF50 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF50 2010
DF50QH 1999,2000,2001,2002,2003,2004,2005,2006,2007
DF50TL 1999,2000,2001,2002,2003,2004,2005,2006,2007
DF60 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF60HL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF60TL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF70 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF70THL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF70TL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DT115 1986,1987,1988,1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000,2001
DT140 1986,1987,1988,1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000,2001
DT150 1998,1999,2000,2001,2002,2003
DT15C 1989,1990,1991,1992,1993,1994,1995,1996,1997
DT200 1998,1999,2000,2001,2002,2003
DT20ELG 1986
DT20ELH 1987
DT20ELJ 1988
DT20ESG 1986
DT20ESH 1987
DT20ESJ 1988
DT20MLG 1986
DT20MLH 1987
DT20MLJ 1988
DT20MSG 1986
DT20MSH 1987
DT20MSJ 1988
DT225 1998,1999,2000,2001,2002,2003
DT25C 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000
DT25ELF 1985
DT25ELG 1986
DT25ELH 1987
DT25ELJ 1988
DT25ESG 1986
DT25ESH 1987
DT25ESJ 1988
DT25MLD 1983
DT25MLE 1984
DT25MLF 1985
DT25MLG 1986
DT25MLH 1987
DT25MLJ 1988
DT25MSD 1983
DT25MSE 1984
DT25MSF 1985
DT25MSG 1986
DT25MSH 1987
DT25MSJ 1988
DT25SF 1985
DT30C 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000
DT30ELD 1983
DT30ESD 1983
DT30LF 1985
DT30MLD 1983
DT30MSD 1983
DT30MSE 1984
DT30SF 1985
DT40C 1986,1987,1988,1989,1990,1991,1992,1993,1994,1995,1996,1997,1998
DT40ECLE 1984
DT40ECLF 1985
DT40ECSE 1984
DT40ECSF 1985
DT40MCLE 1984
DT40MCLF 1985
DT40MCSE 1984
DT40MCSF 1985
DT50ECLE 1984
DT50MCLE 1984
DT60CLE 1984
DT75TCLG 1986
DT75TCLH 1987
DT85TCLF 1985

Information:


Table 1
Code and Description Conditions which Generate this Code Conditions which Generate this Code
1632-9 Backup Engine Control Module abnormal update rate Communication with the backup Electronic Control Module (ECM) cannot be established within three seconds after the Primary ECM is powered up. After communication with the backup ECM has been established, communication stops for one second. The ECM will log the diagnostic code. The backup ECM will not be available for engine control. Note: This procedure checks for an open circuit or for a short circuit in the Cat Data Link. If you are experiencing problems with communications between the Cat® Electronic Technician (ET) and the Electronic Control Module (ECM), refer to Troubleshooting, "Electronic Service Tool Does Not Communicate", before you use this procedure.The Cat Data Link is the standard data link that is used by the ECM to communicate with Cat ET. The ECM communicates with Cat ET to share status information and diagnostic information. Cat ET can also be used to configure the ECM parameters. This information will not be available if communication fails between the ECM and Cat ET.
Illustration 1 g01390276
Schematic for the Cat Data Link
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Remove electrical power from the ECM.
B. Thoroughly inspect connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the Cat Data Link.
D. Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect", for the correct torque values.
Connectors, Pins, and Sockets
Result: The harness and the connectors appear to be OK.
Proceed to Test Step 2.
Result: The connectors and/or the wiring are not OK.
Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.
STOP
Table 3
Resistance Measurements for the Cat Data Link
Connector and Terminal Terminal
P1-8 (Cat Data Link +) All the other terminals on the P1 connector
Negative ground
P1-9 (Cat Data Link -) All the other terminals on the P1 connector
Negative ground
Table 4
Troubleshooting Test Steps Values Results
2. Check for a Short Circuit
A. Disconnect the P1 ECM connector.
B. Disconnect Cat ET from the service tool connector.
C. Measure the resistance between the points that are listed in Table 3. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Open Circuit
Result: Each check of the resistance indicates an open circuit.
Proceed to Test Step 3.
Result: At least one check of the resistance does not indicate an open circuit. There is a short circuit in the harness or in a connector.
Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved.
STOP
3. Check for an Open Circuit
A. Fabricate a jumper wire that is long enough to create a test circuit across two terminals at the service tool connector. Use the jumper wire to create a short circuit between terminals D (Cat Data Link +) and E (Cat Data Link −) on the service tool connector.
B. Measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −).
Resistance
Result: Each check of the resistance checks indicates a short circuit.
1. Connect the J1/P1 connectors. Connect Cat ET to the service tool connector.
2. Check the Cat Data Link for proper operation. If the data link does not operate correctly, there may be a problem with the ECM.
Temporarily install a new ECM. Check the Cat Data Link again. If the new ECM solves the problem, install the original ECM and verify that the original problem returns. If the new ECM operates correctly and the original ECM does not operate correctly, replace the original ECM. Verify that the problem is resolved.
STOP
Result: At least one of the resistance measurements indicates an open circuit. There is an open circuit or excessive resistance in the harness. There may be a problem with a connector.
Repair the wiring and/or the connectors. Replace parts, if necessary. Verify that the original problem is resolved.
STOP


Parts actuator Suzuki:

37725-94301
 
37725-94301 ACTUATOR, NEUTRAL SWITCH
25ELX, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ESD, DT15ESE, DT15ESF, DT15MLD, DT15MLF, DT15MSD, DT15MSE, DT15MSF, DT25ELZ, DT25ESX, DT25ESZ, DT25MLX, DT25MLZ, DT25MSX, DT25MSZ, DT28J, DT28Z, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT3
37725-95300
 
37725-95300 ACTUATOR, NEUTRAL SWITCH
30ELE, 30ESE, 30MLE, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT
67214-94300
 
67214-94300 Actuator
30ELE, 30ESE, 30MLE, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ESD, DT15ESE, DT15ESF, DT15MLD, DT15MLF, DT15MSD, DT15MSE, DT15MSF, DT30ELD, DT30ESD, DT30LF, DT30MLD, DT30MSD, DT30MSE, DT30SF, DT40, DT75TCLD, DT75TCLE, DT85TCLE, DT8LD, DT8LE, DT8LF, DT
37725-94302
 
37725-94302 Actuator, Neutral Switch
DF15, DF15, DF15, DF15S, DF9.9, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, D
Back to top