45231-95200 Suzuki Arm, reverse lock


45231-95200 Arm, reverse lock Suzuki DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELT Arm
45231-95200 Arm, reverse lock Suzuki
Rating:
23

Buy Arm, reverse lock 45231-95200 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50ELB 1977
DT50ELC 1978
DT50ELN 1979
DT50ESB 1977
DT50ESC 1978
DT50ESN 1979
DT50M 1980,1981,1982
DT50MLC 1978
DT50MLN 1979
DT50MSC 1978
DT50MSN 1979
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982
DT65ELC 1978
DT65ELN 1979
DT65ESC 1978
DT65ESN 1979
DT85ELT 1980
DT85TCLT 1980
DT85TCLX 1981
DT85TCLZ 1982
DT85TELT 1980

Information:


Illustration 1 g06226990
Table 1
Item Qty Part Specification Description
1 1 223-9159 Top Piston Ring Install the top piston ring with the side marked "Up-1" toward the top of the piston. Orient the purple stripe face to the right of the end gaps of the piston ring.
Clearance between the ends of the top piston ring in a cylinder liner bore of 145.0 mm (5.71 inch) is 0.40 0.10 mm (0.016 0.004 inch).
Increase in the clearance between the ends of the top piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
Thickness of new top piston ring is 3.845 mm (0.1514 inch).
2 1 344-5153 Piston Ring Install the intermediate piston ring with the side marked "Up-2" toward the top of the piston. Orient the white stripe face to the right of the end gaps of the piston ring.
Clearance between the ends of the intermediate piston ring in a cylinder liner bore of 145.0 mm (5.71 inch) is 0.825 0.125 mm (0.0325 0.0049 inch).
Increase in the clearance between the ends of the intermediate piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
Thickness of new intermediate piston ring is 2.94 mm (0.116 inch).
3 1 246-5659 Piston Ring The ends of the oil control piston ring should be at a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The green stripe faces to the right or left of the piston ring end gap.
Clearance between the groove and the new oil control piston ring in a cylinder liner bore of 145.0 mm (5.71 inch) is 0.55 0.15 mm (0.022 0.006 inch).
Increase in the clearance between the ends of the oil control piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore is 0.08 mm (0.003 inch).
Thickness of new oil control piston ring is 2.980 0.010 mm (0.1173 0.0004 inch).
Width of groove in new piston body assembly for oil control piston ring is 3.020 0.010 mm (0.1189 0.0004 inch).
4 1 524-5565 Piston Pin Thoroughly lubricate the piston pin with clean engine oil before the piston pin is inserted into the piston body assembly and the rod assembly.
Outside diameter of the new piston pin is 59.975 0.005 mm (2.3612 0.0002 inch).
Inside diameter of the new piston pin is 25.1 to 25.7 N m (222.1 to 227.4 lb in).
Length of the new piston pin is 89.8 0.2 N m (66.2 0.1 lb ft).
Bore in the new piston body assembly for the piston pin is 60.095 0.005 mm (2.3659 0.0002 inch).
5 2 250-2940 Pin Retainer Install the pin retainer with the gap at the bottom of the piston as shown in Illustration 1.
6 1 150-1156 Special Bolt Torque to 25 6 N m (221 53 lb in).
A - - Thoroughly lubricate the entire piston with clean engine oil prior to assembly into the cylinder block.
- - - After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 degrees from each other.
Refer to Guideline for Reusable Parts for information on the pistons, the piston pins, and the retaining rings.
The 1U-6431 Piston Ring Groove Gauge Gp is used for measuring the ring grooves in keystone style pistons. Refer to the Special Instruction that is supplied with the piston ring groove gauge group.
The 5P-3519 Piston Ring Groove Gauge Gp is available for checking the ring grooves with straight sides. Refer to the Guideline for Reusable Parts for instructions on the piston ring groove gauge group.


Parts arm Suzuki:

41222-95201
 
41222-95201 Arm, tilt lock
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
41223-95200
 
41223-95200 Arm, tilt stop
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
41223-95201
 
41223-95201 Arm, tilt stop
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
21213-95301
 
21213-95301 Arm, clutch shaft side
DT50ECLE, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MCLE, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT60CLE, DT65ELC, DT65ELN, DT65ESC, DT65ESN
45253-95200
 
45253-95200 Arm, release
DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELT
21230-95500
 
21230-95500 Arm, clutch shaft side
DT75TCLG, DT75TCLH, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
48161-95501-01J
 
48161-95501-01J Arm, trailering lock
DT50, DT50M, DT50W, DT65, DT65, DT85TELN
23210-95500
 
23210-95500 Arm, clutch control
DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLG, DT75TCLH, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
Back to top