09262-10002 Suzuki Bearing

Hints for Cold Weather Operation
If the engine will start, operate the engine until a minimum operating temperature of 80° C (176° F) is achieved. Achieving operating temperature will help prevent the intake valves and exhaust valves from sticking.
The cooling system and the lubrication system for the engine do not lose heat immediately upon shutdown. This means that an engine can be shut down for a period and the engine can still have the ability to start readily.
Install the correct specification of engine lubricant before the beginning of cold weather. Refer to Special Publication, SEBU6251, "Caterpillar Commercial Diesel Engine Fluids Recommendations".
Check all rubber parts (hoses, fan drive belts, ) weekly.
Check all electrical wiring and connections for any fraying or damaged insulation.
Keep all batteries fully charged and warm by ensuring that the engine is allowed to operated at normal operating temperature.
Fill the fuel tank at the end of each shift.
Drain the water from the fuel system. Refer to this Operation and Maintenance Manual, "Fuel System Primary Filter/Water Separator - Drain".
Check the air cleaners and the air intake daily. Check the air intake more often when you operate in snow.
Ensure that the glow plugs are in working order. Refer to Testing and Adjusting Manual, "Glow Plug - Test".
Personal injury or property damage can result from alcohol or starting fluids.Alcohol or starting fluids are highly flammable and toxic and if improperly stored could result in injury or property damage.
Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury.
For jump starting with cables in cold weather, refer to the Operation and Maintenance Manual, "Starting with Jump Start Cables." for instructions.Viscosity of the Engine Lubrication Oil
Correct engine oil viscosity is essential. Oil viscosity affects lubrication properties and wear protection that the oil provides for the engine. Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for the recommended viscosity of oil.Recommendations for the Coolant
Provide cooling system protection for the lowest expected outside temperature. Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for the recommended coolant mixture.In cold weather, check the coolant often for the correct glycol concentration in order to ensure adequate freeze protection.Engine Block Heaters
Engine block heaters (if equipped) heat the engine jacket water that surrounds the combustion chambers. This equipment provides the following functions:
Startability is improved.
Warm up time is reduced.An electric block heater can be activated once the engine is stopped. A block heater can be 110 V or 240 V. The output can be 750/1000 W. Consult your Cat dealer for more information.Idling the Engine
After starting the engine, the engine speed will be governed for a maximum period of 25 seconds. When idling after the engine is started in cold weather, increase the engine rpm from 1000 to 1200 rpm. This idling will warm up the engine more quickly. Maintaining an elevated low idle speed for extended periods will be easier with the installation of a hand throttle. The engine should not be “raced” in order to speed up the warm-up process.While the engine is idling, the application of a light load (parasitic load) will assist in achieving the minimum operating temperature. The minimum operating temperature is 80° C (176° F).Constant speed engines should be allowed to operate at low idle for 3 minutes before used at operational speed. If the low idle option is not available, then operate the engine at operational speed with no load for 2 minutes.Recommendations for Coolant Warm Up
Warm up an engine that has cooled below normal operating temperatures due to inactivity. This warn-up should be performed before the engine is returned to full operation. During operation in very cold temperature conditions, damage to engine valve mechanisms can result from engine operation for short intervals. This damage can happen if the engine is started and the engine is stopped many times without being operated in order to warm up completely.When the engine is operated below normal operating temperatures, fuel and oil are not completely burned in the combustion chamber. This fuel and oil causes soft carbon deposits to form on the valve stems. Generally, the deposits do not cause problems and the deposits are burned off during operation at normal engine operating temperatures.Starting and stopping the engine many times without being operated in order to warm up completely, the carbon deposits become thicker. This issue can cause the following problems:
Free operation of the valves is prevented.
Valves become stuck.
Pushrods may become bent.
Other damage to valve train components can result. For this reason, when the engine is started, the engine must be operated until the coolant temperature is 80° C (176° F) minimum. Carbon deposits on the valve stems will be kept at a minimum. Free operation of the valves and the valve components will be maintained.In addition, the engine must be thoroughly warmed in order to keep other engine parts in better condition. The service life of the engine will be generally extended. Lubrication will be improved. There will be less acid and less sludge in the oil. This better condition will provide longer service life for the engine bearings, the piston rings, and other parts. However, limit unnecessary idle time to 10 minutes in order to reduce wear and unnecessary fuel consumption.The Water Temperature Regulator and Insulated Heater Lines
The engine is equipped with a water temperature regulator. When the engine coolant is below the correct operating temperature jacket water circulates through the engine cylinder block and into the engine cylinder head. The coolant then returns to the cylinder block via an internal passage that bypasses the valve of the coolant temperature regulator. This system ensures that coolant flows around the engine under cold operating conditions. The water temperature regulator begins to open when the engine jacket water has reached the correct minimum operating temperature. As the jacket water coolant temperature rises above the minimum operating temperature the water temperature regulator opens further allowing more coolant through the radiator to dissipate excess heat. The progressive opening of the water temperature regulator operates the progressive closing