09262-40003 Suzuki BEARING, UNDER (40X80X18)

DIRECT DRIVE AND SPECIAL APPLICATION6. Disconnect interlock linkage (1) at the lever on the flywheel clutch.7. Disconnect clip (2) from the mounting bracket for the hydraulic tank.
DIRECT DRIVE AND SPECIAL APPLICATION8. Disconnect rod assembly (3) and rod assembly (5) from the lever on the flywheel clutch. Remove lever (4) from the flywheel clutch.
DIRECT DRIVE AND SPECIAL APPLICATION9. Remove tube assemblies (9) and (8) from the flywheel clutch. Disconnect hose assembly (6) and hose assembly (7) from the flywheel clutch.
POWER SHIFT10. Remove bracket (11) and clip (12) from the frame of the machine.11. Disconnect hose assemblies (10) and (13) for the engine and transmission oil coolers.
POWER SHIFT12. Disconnect oil temperature line (15) from the torque converter outlet relief valve. Disconnect tube assembly (14) from the valve.
POWER SHIFT13. Disconnect hose assembly (18) from the sequence relief valve. Disconnect hose assembly (17) from the sequence relief valve.14. Disconnect tube assembly (19) from the scavenge pump. Disconnect hose assembly (16).
Before any service is performed on the refrigerant compressor for air conditioning, see subjects: Preparation Of System For Replacement Or Repair Of Components and Refrigerant Hoses and Lines in Air Conditioning and Heating Service Manual SENR7454.
15. Remove plate (20) and two refrigerant hoses (21) from the compressor.16. Remove clip (22) from the frame of the machine.17. Disconnect two wires (23) from the refrigerant compressor. 18. Disconnect two rod assemblies (25) and (26) from the bellcranks for the hydraulic controls.19. Disconnect governor control rod (24) at the bellcrank that is fastened to the bracket on the dash.20. Disconnect positive battery cable (28) from the electric starting motor. Disconnect wire harness (27) for the back-up warning alarm. 21. Turn cock (32) and valve (33) to the "OFF" position.22. Remove clip (30) and clip (31). Disconnect hose (29) at the water pump adapter. Disconnect hose (34) from the valve in the bonnet for the transmission oil cooler. 23. Disconnect tube assemblies (37) and (38) for the oil and fuel pressure gauges.24. Remove inlet tube assembly (39) from the pump. Remove water temperature sending unit line (36). Remove bolt (35) that holds the clip for the battery cable. Move the battery cable away from the engine. 25. Disconnect fuel lines (40).26. Drain the oil from the hydraulic tank. 27. Remove four bolts (44) and two bolts (42). Remove tube assembly (43) and tube assembly (41). Remove the support for the tube assemblies from the cylinder head. 28. Fasten a hoist to air cleaner assembly (46). Disconnect hose (47) and hose (45) from the air cleaner assembly. Remove the four bolts that hold the air cleaner assembly to the inlet manifold. Remove the air cleaner assembly. The weight of the air cleaner assembly is 32 kg (70 lb.). 29. Remove bracket (48) from the hydraulic tank. 30. Disconnect rod assembly (49) from the bellcrank in bracket (50). Remove bracket (50) from the dash.31. Remove the plate from the top of the dash inside of the cab. Disconnect the fuel pressure tube assembly from the gauge in the dash. Disconnect the tube assembly for the oil pressure from the gauge. Put identification on the tube assemblies and remove them from the dash. 32. Disconnect rod assemblies (51) and (52) from the bellcrank for the hydraulic controls. Put identification on the rods for correct installation. 33. Remove hose (53) from the breather group in the valve cover.34. Install tooling (A) in the cylinder head as shown. Fasten a hoist with chains and a spreader bar to the engine. The spreader bar will prevent damage to the turbocharger from the chains.35. Remove the two bolts that hold the engine front support to the frame of the machine.36. Remove four bolts, two on each side of the machine, that hold the flywheel housing to the frame of the machine. Remove engine (54) from the machine. The weight of the engine, hydraulic tank and flywheel clutch is 1310 kg (2900 lb.). The weight of the engine, hydraulic tank and torque converter is 1350 kg (3000 lb.). 37. Remove shims (55) at each rear position on the frame of the machine. Put identification on the shims for correct installation.Install Engines
1. Install original amount of shims (1) on each side of the frame of the machine at the rear. 2. Fasten a hoist to engine (2) and put it in position on the frame of the machine. Make sure the flywheel housing is in position over the dowels in the frame at the rear.3. Install the two bolts that hold the engine front support to the frame of the machine. Tighten the bolts to a torque of 440 35 N m (325 25 lb.ft.).4. Install the four bolts, two on each side of the machine, that hold the flywheel housing to the frame of the machine. Tighten the bolts to a torque of 270 35 N m (200 25 lb.ft.).5. Connect the hose to the breather group on the valve cover. 6. Connect rod assemblies (3) and (4) to the bellcrank for the hydraulic controls. Make sure the rods are in the correct positions. 7. Install tube assemblies (5) and (6) for the fuel pressure and oil pressure through the holes in the rear of the dash. Connect the tube assemblies to the correct gauges in the dash. Install the plate over the opening in the top of the dash. 8. Install bracket (7) on the dash. Connect rod assembly (8) to the bellcrank in bracket (7). 9. Install bracket (9) and the bolts that hold it. 10. Install a new gasket on the intake manifold for the air cleaner assembly. Fasten a hoist to air cleaner assembly (10) and put it in position on the intake manifold (11) on the air cleaner assembly. Tighten the clamps that hold it. Install hose (12) on the turbocharger and tighten the clamps that hold it. 11. Install support (15). Install tube assemblies (13) and (14).12. Fill the hydraulic tank with oil to the correct level. See Lubrication and Maintenance Guide. 13. Connect fuel