11301-98J01 Suzuki BLOCK SET, CYLINDER


11301-98J01 BLOCK SET, CYLINDER Suzuki DF200, DF200, DF225, DF225, DF250, DF250, DF300, DF300 BLOCK

Buy BLOCK SET, CYLINDER 11301-98J01 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Suzuki entire parts catalog list:

DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF300 2007,2008,2009
DF300 2010

Information:


Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
E265(3) User Defined Shutdown     The inputs from the ground level shutdown switch to the Electronic Control Module (ECM) have changed states.     The engine will shut down. The code is logged.    
267-3 Remote Shutdown Input voltage above normal     Both of the switch contacts of the ground level shutdown switch are in the open state.     If both of the switch contacts from the ground level shutdown switch change to the same state and the engine is running, the engine will continue to run. The code is logged.    
267-4 Remote Shutdown Input voltage below normal     Both of the switch contacts of the ground level shutdown switch are in the closed state.    The ground level shutdown switch provides the ability to shut down the engine. The engine's ECM remains active. Caterpillar Electronic Technician (ET) can be used to communicate with the ECM. The ground level shutdown switch must be returned to the RUN position and the engine rpm must be zero before the ECM will allow the engine to start.To shut down the engine, lift the red cover guard and toggle the ground level shutdown switch to the SHUTDOWN position. The ECM reads the position of the ground level shutdown switch. If the engine is running, the ECM disables the fuel injection. The status screen will display "INJECTION DISABLED" and "REMOTE SHUTDOWN".The ECM will not allow the engine to start if the status for the ground level shutdown switch is "REMOTE SHUTDOWN".
Illustration 1 g01397149
Schematic
Illustration 2 g01303342
P1 ECM connector (P1-54) user defined shutdown (NO) (P1-56) user defined shutdown (NC)Test Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connector J1/P1. Thoroughly inspect the connectors for the ground level shutdown switch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ground Level Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector. Start Cat ET.
Turn the keyswitch to the ON position.
Observe the status of the ground level shutdown switch on Cat ET.
Operate the ground level shutdown switch. Observe the status of the ground level shutdown switch on Cat ET.Expected Result:The status of the ground level shutdown switch on Cat ET is REMOTE SHUTDOWN when the ground level shutdown switch is in the SHUTDOWN position.Results:
OK - The status of the ground level shutdown switch on Cat


Parts block Suzuki:

11301-93J02
 
11301-93J02 BLOCK SET, CYLINDER
DF200, DF200T, DF200Z, DF225, DF225T, DF225Z, DF250, DF250T, DF250Z
11301-93J01
 
11301-93J01 BLOCK SET, CYLINDER
DF200, DF200T, DF200Z, DF225, DF225T, DF225Z, DF250, DF250T, DF250Z
11301-93J03
 
11301-93J03 BLOCK SET, CYLINDER
DF200, DF200, DF225, DF225, DF250, DF250
11301-93J10
 
11301-93J10 BLOCK SET, CYLINDER
DF200, DF200, DF225, DF225, DF250, DF250
11301-98J03
 
11301-98J03 BLOCK SET, CYLINDER
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF300, DF300
11301-98J00
 
11301-98J00 BLOCK SET, CYLINDER
DF200, DF225, DF250, DF300
11301-98J21
67256-98J00
 
67256-98J00 BLOCK, NEUTRAL LOCK
DF250A, DF300, DF300, DF300A
Back to top