01907-10608 Suzuki Bolt


01907-10608 Bolt Suzuki DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELT Bolt
01907-10608 Bolt Suzuki
Rating:
93

Buy Bolt 01907-10608 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 6-2
 

Compatible models:

Suzuki entire parts catalog list:

DT85ELT 1980
DT85TCLT 1980
DT85TCLX 1981
DT85TCLZ 1982
DT85TELT 1980

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119693
Remove bolts (1). Remove rocker shaft assembly (2) from valve mechanism cover base (6). Remove valve push rods (4).Note: Mark the valve push rods for identification of location for assembly.
Remove bridge assemblies (3) from the valve stems.Note: Mark the bridge assemblies with identification of location for assembly.
To remove push rod (5), it is necessary to remove valve mechanism cover base (6).Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 3 g01131377
Illustration 4 g01158612
Valve bridge for dowel installations
Illustration 5 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
Valve bridge assemblies for dowel installations have an adjustment screw and a jam nut. Use the following procedure to install this configuration.
Loosen adjustment screw (11) and jam nut (12) on bridge assembly (3).
Coat these items with clean engine oil: the dowels, the receptacle of the bridge assembly for the dowels and the uppermost contact surface of bridge assembly (3).
Place bridge assembly (3) into position on the dowel. Apply a downward force of 5 to 45 N (1 to 10 lb) on the uppermost contact surface of bridge assembly (3). While you apply the force, turn adjustment screw (11) until the adjustment screw contacts the valve stem.
Turn the adjustment screw for an additional 20 to 30 degrees (1/3 to 1/2 of the hex).
Hold the adjustment screw in position and tighten jam nut (12) to a torque of 30 4 N m (22 3 lb ft).
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 5.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts to a torque of 215 40 N m (160 30 lb ft).
Illustration 6 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread, tighten to a torque of 120 15 N m (89 11 lb ft). If nut (10) is 1/2 inch thread, tighten to a torque of 70 15 N m (52 11 lb ft).End By:
Install the valve mechanism cover.


Parts bolt Suzuki:

01107-06208
 
01107-06208 Bolt
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT14C, DT14D, DT14F, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ESD, DT15ESE, DT15ESF, DT15MLD, DT15MLF, DT15MSD, DT15MSE, DT15MSF, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT1
09100-10113
 
09100-10113 Bolt, transom
DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
09100-12019
 
09100-12019 Bolt
DT50, DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TEL
09100-10123
 
09100-10123 Bolt
DT50, DT50, DT50M, DT50W, DT65, DT65, DT75TCLD, DT75TCLE, DT75TCLF, DT85ELT, DT85TCLD, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
09100-10149
 
09100-10149 Bolt
DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLG, DT75TCLH, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
09100-08153
 
09100-08153 Bolt
DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ESD, DT15ESE, DT15ESF, DT15MLD, DT15MLF, DT15MSD, DT15MSE, DT15MSF, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT, DT9.9ELD, DT9.9ELE, DT9.9ELF, DT9.9ESD, DT9.9ESE, DT
13611-95211
 
13611-95211 BOLT
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT50, DT50, DT50M, DT50W, DT60CLD, DT
09100-08160
 
09100-08160 BOLT
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT35TCLH, DT35TCLJ, DT
Back to top