09100-06123 Suzuki Bolt


09100-06123 Bolt Suzuki DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH, DT6LE, DT6LF, DT6SE, DT6SF, DT8LG, DT8LH, DT8SG, DT8SH Bolt
09100-06123 Bolt Suzuki
Rating:
8

Buy Bolt 09100-06123 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Suzuki entire parts catalog list:

DT4LF 1985
DT4LG 1986
DT4LH 1987
DT4SF 1985
DT4SG 1986
DT4SH 1987
DT6LE 1984
DT6LF 1985
DT6SE 1984
DT6SF 1985
DT8LG 1986
DT8LH 1987
DT8SG 1986
DT8SH 1987

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
A(2) 585-0005 Crankshaft Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C - E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) This Tool is used in the aperture for the electric starting motor.
(2) The Crankshaft Turning Tool is used on the front pulley.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all the components.
Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the piston and to the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g06361356
Install Tooling (B) onto piston (4). Ensure that the piston ring gaps are 120 degrees apart.Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g06360869
Install connecting rod cap (2) onto connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to connecting rod (3). Use Tooling (C) to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 9 to install the remaining pistons and connecting rods.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts bolt Suzuki:

09128-06014
 
09128-06014 Bolt, Adjusting
DF4, DF4, DF4, DF46, DF4L, DF6, DF6, DF6, DF6L, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16SB, DT16SC, DT16SN, DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH, DT5LC, DT5LD, DT5LN, DT5LT, DT5LX, DT5LZ, DT5SC, DT5SD, DT5SN, DT5ST, DT5SX, DT5SZ, DT6LE,
13613-98300
 
13613-98300 Bolt
DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ, DT4, DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH, DT5LD, DT5LT, DT5LX, DT5LZ, DT5SD, DT5ST, DT5SX, DT5SZ, DT5Y, DT6, DT6LE, DT6LF, DT6SE, DT6SF
13613-98100
 
13613-98100 Bolt
DT15 MLE, DT15C, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ELJ, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15ESJ, DT15MLD, DT15MLF, DT15MLG, DT15MLH, DT15MLJ, DT15MSD, DT15MSE, DT15MSF, DT15MSG, DT15MSH, DT15MSJ, DT16LT, DT16LT, DT16LT, DT
09100-06122
 
09100-06122 BOLT
DT2D, DT2E, DT2F, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV,
09100-10190
 
09100-10190 Bolt
DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DT40C, DT6, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LG, DT8LH, DT8SD, DT8SE, DT8SF, DT8SG, DT8SH
09100-06113
Bolt
09100-06113 Bolt
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF25, DF250, DF250, DF250, DF250T, DF250Z, DF25Q, DF25Q(
09100-08220
 
09100-08220 Bolt
DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ELJ, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15ESJ, DT15MLD, DT15MLF, DT15MLG, DT15MLH, DT15MLJ, DT15MSD, DT15MSE, DT15MSF, DT15MSG, DT15MSH, DT15MSJ, DT4LF, DT4LG, DT4LH, DT4SF, DT4SG
09100-06103
 
09100-06103 Bolt
30ELE, 30ESE, 30MLE, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ELJ, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15ESJ, DT15MLD, DT15MLF, DT15MLG, DT15MLH, DT15MLJ, DT15MSD, DT15MSE, DT15MSF, DT15MSG, DT15MSH, DT15MSJ, DT20ELG, DT2
Back to top