36617-98J00 Suzuki BRACKET, HARNESS


36617-98J00 BRACKET, HARNESS Suzuki DF250A, DF300, DF300, DF300A BRACKET
36617-98J00 BRACKET, HARNESS Suzuki
Rating:
98

Buy BRACKET, HARNESS 36617-98J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Compatible models:

Suzuki entire parts catalog list:

DF250A 2011
DF300 2007,2008,2009
DF300 2010
DF300A 2011

Information:

Disassemble Turbocharger (Schwitzer F552) (Industrial Engine)
start by: a) remove turbocharger 1. Install turbocharger in tool group (A). Remove "V" clamp (2) and compressor housing (1). 2. Remove "V" clamp (3). Remove the cartridge housing (5) from the turbine housing (4). 3. Put the cartridge housing in tool (B). Remove the nut (6) that holds the compressor wheel (7). Remove the compressor wheel.
When the nut is loosened, do not put a side force on the shaft.
4. Remove the cartridge housing from tool (B). Remove the turbine wheel (9) and shaft from the cartridge housing. Remove seal ring (8) from the shaft. 5. Remove the snap ring that holds insert (10) in the cartridge housing. Remove the insert with tooling (C). 6. Remove the sleeve (13) from the insert (11). Remove the two seal rings (12) from the insert. 7. Remove deflector (14), ring (16), sleeve (15), bearing (18) and ring (17) from the cartridge housing. If the oil hole is not open this will cause a bearing failure. 8. Remove the snap ring that holds bearing (19) in the cartridge housing. Remove bearing (19). Remove snap ring (20) with tool (D). 9. Remove the snap ring that holds bearing (21) in place with tool (D). Remove bearing (21) and sleeve (22) from the cartridge housing. 10. Turn the cartridge housing over. Remove snap ring (23). Remove shroud (24). 11. Remove snap ring (25) from the cartridge housing with tool (D).12. Inspect all parts and install new parts as needed.Assemble Turbocharger (Switzer F522) (Industrial Engine)
1. Make sure all oil passages are open and clean. Put engine oil on all parts before assembly. 2. Install snap ring (1) in the cartridge housing with tool (A). Install the snap rings with the round side toward the bearing. 3. Install shroud (4) on the housing. Turn the shroud to make sure it is down on the housing even. The high part (2) on the housing will keep the shroud from turning on the housing after assembly.4. Install the snap ring (3). 5. Turn the cartridge housing over. Install sleeve (6) and bearing (5). Install the snap ring that holds bearing (6) in the cartridge housing with tool (A). 6. Install snap ring (8) with tool (A). Install bearing (7). Install the snap ring that holds bearing (7) in place. Install the snap rings with the round side toward the bearing. 7. Install ring (12), bearing (13), sleeve (10), ring (11) and deflector (9) in the housing.
The oil hole in bearing (13) must be open and clean.
8. Install seal rings (15) in sleeve (16). Install the sleeve in insert (14). 9. Check O-ring seal (17). Replace the seal if necessary. Install insert (18) in cartridge housing (19). Put 4L7464 Silicone Grease in the groove for seal ring (20) at assembly to one half or more of the depth of the groove all the way around the groove. 10. Put clean engine oil on shaft (21). Install seal ring (20) on the shaft. Install the shaft in the cartridge housing. 11. Put cartridge housing in tool (B). Install compressor wheel (22) on the shaft. Put clean engine oil on the shaft threads (23). Install the nut that holds the compressor wheel to the shaft. Tighten the nut to a torque of 22 2 lb.ft. (28 3 N m).
When nut is tightened, do not put a side force on the shaft.
12. Install turbine housing in tool group (C). Install cartridge housing in turbine housing. Install the "V" clamp that holds the cartridge housing to the turbine housing. Put 5P3931 Anti-Seize Compound on the threads of the "V" clamp. 13. Check O-ring seal (24). Replace the seal if necessary. Install the compressor housing to the cartridge housing. Install the "V" clamp that holds the compressor housing to the cartridge housing. 14. Install turbocharger in tool group (D). Loosen the "V" clamp nuts. Turn housings until they are in alignment. The oil drain hole on the cartridge housing and the exhaust opening on the turbine housing must be parallel to the tool base. The air outlet opening on the compressor housing must be at an angle of 63° from a vertical line. Tighten the "V" clamp nuts to a torque of 120 10 lb.in. (13.6 1.1 N m).end by: a) install turbocharger


Parts bracket Suzuki:

41111-93J11-0EP
 
41111-93J11-0EP BRACKET, CLAMP STBD (BLACK)
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z, DF300, DF300
41111-93J12-0EP
 
41111-93J12-0EP BRACKET, CLAMP STBD (BLACK)
DF200, DF200, DF225, DF225, DF250, DF250, DF300, DF300
41111-93J14-0EP
 
41111-93J14-0EP BRACKET, CLAMP STBD (BLACK)
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF300, DF300, DF300A
41121-93J03-0EP
 
41121-93J03-0EP BRACKET, CLAMP PORT (BLACK)
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z, DF300, DF300
15671-93J00
 
15671-93J00 BRACKET, VAPOR SEPARATOR
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
18417-93J00
 
18417-93J00 BRACKET, PURGE VALVE
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
36617-93J00
 
36617-93J00 BRACKET, HARNESS
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A, DF70A, DF70A, DF70A, DF80A, DF8
13134-98J00
 
13134-98J00 BRACKET, COLLECTOR
DF250A, DF300, DF300, DF300A
Back to top