09307-26004 Suzuki BUSHING

1. Disconnect tube assemblies (1) and (2) and gaskets. Check gaskets for wear or damage. Replace if necessary. A bracket holding tube assembly (1) to the engine may require removal for ease in the turbocharger removal. When installing, apply 5P3931 Anti-Seize Compound on the bolts that hold the oil supply line. 2. Loosen two hose clamps (3).3. Slide hose assembly (4) off of the turbocharger. 4. Remove four bolts (5) When installing, apply 5P3931 Anti-Seize Compound on the bolts that hold the turbocharger and exhaust elbow to the manifold. Tighten the bolts to a torque of 55 5 N m (41 4 lb ft).5. Disconnect clamp (8) from muffler (6).6. Remove turbocharger assembly (9) from the engine. Check the gasket and O-ring for wear or damage. Replace if necessary.7. Move the turbocharger assembly to a work bench and remove tube assembly (7).End By:a. install hood assemblyb. install rear engine cowlingDisassemble Turbocharger
Start By:a. remove turbocharger assembly 1. Install the turbocharger on Tool (A) as shown.2. Put alignment marks on the three housings of the turbocharger for correct alignment during assembly. Loosen clamp (2), and remove the clamp and housing (1) from housing assembly (3). 3. Loosen clamp (4), and remove housing assembly (3) from housing (5). 4. Put the cartridge group in position in Tool (B) as shown.
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
5. Use a 5S9566 Sliding T-Wrench and a universal socket (6) to remove the nut that holds the compressor wheel to the wheel assembly.6. Remove compressor wheel (7) and the shims from wheel assembly (8).7. Remove housing assembly (3) from wheel assembly (8). 8. Remove ring (9) and backplate (10) from wheel assembly (8). 9. Use Tool (C), and remove snap ring (11) from housing assembly (3). 10. Remove insert (12) and sleeve (13) from housing assembly (3). 11. Remove ring (14) from sleeve (13). 12. Remove two screws (15) and deflector (16) from housing assembly (3). 13. Remove ring (18) and bearing assembly (17) from the housing assembly. 14. Remove sleeve (19) and ring (20) from the housing assembly. 15. Remove O-ring seal (23) from the housing assembly.16. Use Tool (D), and remove snap ring (22) from the housing assembly.17. Remove bearing (21). Remove the snap ring behind the bearing with Tool (D). 18. Use Tool (D), and remove snap ring (25) from the housing assembly.19. Remove bearing (24). Remove the snap ring behind the bearing with Tool (D).20. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction, Form No. SMHS6854, for Turbocharger Reconditioning. Also see Guidelines For Reuseable Parts, Form No. SEBF8018.Assemble Turbocharger
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, pour clean engine oil into the oil inlet of the turbocharger.
Make sure that the snap rings that hold bearings (2) and (5) in position in housing assembly (3) are installed with the round edge of the outside diameter toward the bearing.
2. Install the snap ring behind bearing (2) with tool (A).3. Install bearing (2) in housing assembly (3).4. Use Tool (A), and install snap ring (1) in the housing assembly. 5. Install the snap ring behind bearing (5) with Tool (A).6. Install bearing (5) in the housing assembly.7. Use Tool (A), and install snap ring (4) in the housing assembly. 8. Put wheel assembly (8) in position on Tool (B) as shown.9. Put backplate (7) in position on the wheel assembly. Put 6V2055 High Vacuum Grease in the groove for seal ring (6) at assembly to one half or more of the depth of the groove all the way around.10. Install ring (6) in the groove in wheel assembly (8). 11. Put housing assembly (3) in position on wheel assembly (8). 12. Install ring (9) and sleeve (10) on the wheel assembly. 13. Make sure screen (10) is in place in bearing assembly (11). 14. Install bearing assembly (11) over the sleeve. Make sure the screen in the bearing assembly is facing down when it is installed.15. Put ring (12) in position on bearing assembly (11). 16. Put deflector (14) in position in the housing assembly, and install two screws (13). Put 6V2055 High Vacuum Grease in the groove of sleeve (15) to one half or more of the depth of the grooves all the way around.17. Install ring (16) in the groove in sleeve (15). 18. Put sleeve (15) in position in insert (17). Install the insert and sleeve (15) as an assembly. 19. Use Tool (C), and install snap ring (18) to hold insert (17) in place. 20. Put wheel (21) in position in compressor housing (20). Center the wheel in the compressor housing.21. Use a straight edge and a depth micrometer (19), and measure the distance between the wheel seating face and the compressor housing mounting face [dimension (X] in four places. Find the average of the measurements. 22. Use a depth micrometer (19) to measure the distance between the face of housing assembly (3) and the surface of sleeve (15) [dimension (Y)].23. Use a depth micrometer (19), and measure the distance between the surface of housing assembly (3) and the compressor housing mounting face [dimension (Z)].24. Calculate the necessary shim thickness as follows:Dimension Z-Dimension Y-Dimension X+(0.23 to 0.28 mm (.009 to .011 in)= Correct Shim Thickness The shims must be of uniform thickness and free of burrs and other imperfections. The total shim thickness should be 0.13 mm to 0.41 mm (.005 to .016 in.) and consist of one or two shims.25. Install wheel (21) at room temperature as follows:a. Put the correct amount of shims and wheel (21) in position on the wheel assembly.b. Put a small amount of clean engine