09401-13402 Clip Suzuki
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20M
Clip
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Boat Engine Fuel Hose Assy Connector Pump for Suzuki 65700-95204/95205/87D80/87D82/87D83/87D84/87D85 DT DF 8HP-65HP Outboard, Length 10ft/3m, Coupler I.D. : Tank Side 13mm, Engine Side 11mm
SouthMarine Include Items: HOSE ASSY, FUEL 65700-95204, CONNECTOR, FEMALE FUEL ID:11 65750-98505, CONNECTOR, FEMALE FUEL ID:13 65750-93000, CLIP 09401-13402, PUMP, SQUEEZE 65770-99702 || For Suzuki Outboard Models: 25EL, DT8, DT16, DT9.9, DT25, DT28, DT30, DT35, DT40, DT50, DT60, DT65 (From Year 1980- 1984) || For Suzuki Part Number: 65700-95204/95205/87D17/87D80/87D82/87D83/87D84/87D85 || Fuel Line Inner Diameter 1/4in/6mm, Length 10ft/3m || Tank Side Coupler I.D. 13 mm 65750-98500, Engine Side Coupler I.D. 11 mm 65750-98505
SouthMarine Include Items: HOSE ASSY, FUEL 65700-95204, CONNECTOR, FEMALE FUEL ID:11 65750-98505, CONNECTOR, FEMALE FUEL ID:13 65750-93000, CLIP 09401-13402, PUMP, SQUEEZE 65770-99702 || For Suzuki Outboard Models: 25EL, DT8, DT16, DT9.9, DT25, DT28, DT30, DT35, DT40, DT50, DT60, DT65 (From Year 1980- 1984) || For Suzuki Part Number: 65700-95204/95205/87D17/87D80/87D82/87D83/87D84/87D85 || Fuel Line Inner Diameter 1/4in/6mm, Length 10ft/3m || Tank Side Coupler I.D. 13 mm 65750-98500, Engine Side Coupler I.D. 11 mm 65750-98505
Compatible models:
20ELB
20ELC
20ELN
25ELB
25ELC
25ELN
25ELT
25ELX
DT14C
DT14D
DT14F
DT16LB
DT16LC
DT16LN
DT16LT
DT16SB
DT16SC
DT16SN
DT16ST
DT20ESB
DT20ESC
DT20ESN
DT20MLB
DT20MLC
DT20MLN
DT20MSB
DT20MSC
DT20MSN
DT25ELZ
DT25ESB
DT25ESC
DT25ESN
DT25EST
DT25ESX
DT25ESZ
DT25MLB
DT25MLC
DT25MLN
DT25MLT
DT25MLX
DT25MLZ
DT25MSB
DT25MSC
DT25MSN
DT25MST
DT25MSX
DT25MSZ
DT28F
DT28G
DT28J
DT28Z
DT3.5LN
DT3.5LT
DT3.5LX
DT3.5LZ
DT3.5SN
DT3.5ST
DT3.5SX
DT3.5SZ
DT35ELT
DT35ELX
DT35ELZ
DT35EST
DT35ESX
DT35ESZ
DT35MLT
DT35MLX
DT35MLZ
DT35MST
DT35MSX
DT35MSZ
DT40ELT
DT40ELX
DT40ELZ
DT40EST
DT40ESX
DT40ESZ
DT40MLT
DT40MLX
DT40MLZ
DT40MSX
DT40MSZ
DT50
DT50M
DT50W
DT5LC
DT5LN
DT5LT
DT5LX
DT5LZ
DT5SC
DT5SN
DT5ST
DT5SX
DT5SZ
DT65
DT7.5LB
DT7.5LC
DT7.5LN
DT7.5SB
DT7.5SC
DT7.5SN
DT85ELT
DT85TCLT
DT85TCLX
DT85TCLZ
DT85TELN
DT85TELT
DT8LT
DT8LX
DT8LZ
DT8ST
DT8SX
DT8SZ
DT9.9LT
DT9.9LX
DT9.9LZ
DT9.9ST
DT9.9SX
DT9.9SZ
Suzuki
Suzuki entire parts catalog list:
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
25ELB 1977
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
25ELT 1980
- Fuel Gauge Hose » 09401-13402
- Fuel Gauge Hose » 09401-13402
- Fuel Gauge Hose » 09401-13402
- Fuel Gauge Hose » 09401-13402
- Fuel Gauge Hose » 09401-13402
- Fuel Gauge Hose » 09401-13402
- Fuel Tank 2 - E13 » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 - E13 » 09401-13402
- Fuel Tank 1 » 09401-13402
DT16LB 1977
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
DT20MLB 1977
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
- Fuel Hose » 09401-13402
DT20MSB 1977
- Fuel Tank 1 » 09401-13402
- Fuel Tank 2 » 09401-13402
- Fuel Hose » 09401-13402
Information:
Introduction
This Special Instruction provides the procedure to install the 466-1958 Heater Kit, which is a single heater for the breather canister inlet. This is required when temperatures are expected below -18C (0F). This heater became standard equipment for machines built after the serial number effectivity listed in this document.Note: 0W-40 engine oil is required. Refer to Operation and Maintenance Manual. Usage of a block heater and heavy-duty battery are also recommended.Note: The 466-1959 Heater Kit is another crankcase breather heater that is installed in the outlet hose of the crankcase breather canister. This is also required when temperatures are expected below -18C (0F).Note: The latest machine software is required, which will elevate low idle in cold weather to increase engine temperature. The latest software also has the appropriate minimum fan speed settings. The minimum fan speed must be calibrated. This also requires installation of the optional demand fan. Refer to the last section of this document for this procedure and serial number effectivity when the demand fan became standard equipment.Note: In territories that operate in ambient temperatures of −32° C (−26° F) and colder, a rear door cover is also required. If hauling a machine with the engine running, the rear door cover is required when ambient temperatures are expected below 0C (32F). The following is the information for the rear door covers: For sales models 236D, 242D, 257D, and 259D, the rear door cover is 452-2243 Cover Kit as per Special Instruction, REHS8736, "Installing the Winter Cover Kit". For sales models 246D, 262D, 277D, 279D, 287D, and 289D, the rear door cover is 452-0239 Heater Kit as per Special Instruction, REHS8737, "Installing the 452-0239 Winter Cover Kit".Note: Not performing the above can result in freezing of the breather system and engine failure.Parts List
Table 1
Qty Part Number Description
1 466-1958 Heater Kit Installation Procedure
Illustration 1 g03730673
Loosen hose clamp (1) and hose clamp (A). Save hose clamp (1) for reuse and discard hose clamp (A).
Remove two hose clamps (B). Remove and discard the tube, hose, and clamps (B).
Remove bolt (2) and save the part for reuse.
Illustration 2 g03730674
Loosen two hose clamps (3). Remove and discard tube assembly (C).
Illustration 3 g03730675
Install tube assembly (4) from the 466-1958 Heater Kit using two original hose clamps (3) in orientation as shown in Illustration 3.
Illustration 4 g03730676
Install tube (6) using bolt (2) that is saved in Step 3. Install tube (6) to the valve cover hose using original hose clamp (1).
Install hose (7), heater (8), and hose (9) with hose clamp (11) and hose clamp (12). Ensure that heater (8) is positioned as shown in Illustration 3.
Install hose (5) using hose clamp (10).
Illustration 5 g03730677
Disconnect two-pin connector (14) and connect the heater harness.
Route the harness above the Exhaust Gas Recirculation (EGR) coolant hose. Route the harness to the breather hose that runs from the breather canister to the intake.
Install tie straps (15) to secure the connector on the front of the engine, to the EGR coolant hose, and to the breather hose. Refer to Illustration 5.
Connect the harness to the in-line heater.
Bundle and secure any excess harness. Ensure that the harness does not rub other engine components and is not in contact with the exhaust manifold.Machine Software Update
Flash the machine ECM with the 464-6052 Machine Software Gp or later version.Note: The machine software elevates idle speed during cold-weather operation, when the parking brake and the hydraulic lockout are both engaged.Note: If the coolant temperature is less than or equal to 5° C (41° F), then low idle is limited to 1400 rpm. If ambient air temperature is less than or equal to 0° C (32° F) or if coolant temperature is less than or equal to 70° C (158° F) for 7 minutes, then low idle is limited to 2000 rpm.Note: When the machine ECM is flashed, engine diagnostic codes will be created due to the loss of communication between the engine ECM and the machine ECM. These codes will show up as "CAN DATA LINK" codes. After flashing the machine ECM, turn the key switch OFF and back ON (engine not running) and these codes will change from active to logged. With the key switch ON (engine not running) clears the logged codes. If the codes still do not clear, ensure the "All ECM" box is NOT checked.Calibration Procedure for Minimum Fan Speed
The demand fan is a required component to complete this update to decrease the minimum engine fan speed.For the 246D - S/N:BYF, 262D - S/N:DTB, 277D - S/N:FMT, 279D - S/N:GTL, 287D - S/N:HMT, and 289D - S/N:TAW, the demand fan is standard.For the 236D - S/N:BGZ, 242D - S/N:DZT, 257D - S/N:EZW, and 259D - S/N:FTL, the demand fan is an option. For these models if the machine has the standard fan, the demand fan will need to be installed. Refer to 258-2579 Hydraulic Fan Motor and Mounting Gp in SIS web. After installing these components, use the Cat® Electronic Technician (Cat ET) Service Tool to change the configuration for the Demand Fan "Installed".
Calibrate the "Minimum Fan Speed" in the machine ECM.
Illustration 6 g03730679
Foll
This Special Instruction provides the procedure to install the 466-1958 Heater Kit, which is a single heater for the breather canister inlet. This is required when temperatures are expected below -18C (0F). This heater became standard equipment for machines built after the serial number effectivity listed in this document.Note: 0W-40 engine oil is required. Refer to Operation and Maintenance Manual. Usage of a block heater and heavy-duty battery are also recommended.Note: The 466-1959 Heater Kit is another crankcase breather heater that is installed in the outlet hose of the crankcase breather canister. This is also required when temperatures are expected below -18C (0F).Note: The latest machine software is required, which will elevate low idle in cold weather to increase engine temperature. The latest software also has the appropriate minimum fan speed settings. The minimum fan speed must be calibrated. This also requires installation of the optional demand fan. Refer to the last section of this document for this procedure and serial number effectivity when the demand fan became standard equipment.Note: In territories that operate in ambient temperatures of −32° C (−26° F) and colder, a rear door cover is also required. If hauling a machine with the engine running, the rear door cover is required when ambient temperatures are expected below 0C (32F). The following is the information for the rear door covers: For sales models 236D, 242D, 257D, and 259D, the rear door cover is 452-2243 Cover Kit as per Special Instruction, REHS8736, "Installing the Winter Cover Kit". For sales models 246D, 262D, 277D, 279D, 287D, and 289D, the rear door cover is 452-0239 Heater Kit as per Special Instruction, REHS8737, "Installing the 452-0239 Winter Cover Kit".Note: Not performing the above can result in freezing of the breather system and engine failure.Parts List
Table 1
Qty Part Number Description
1 466-1958 Heater Kit Installation Procedure
Illustration 1 g03730673
Loosen hose clamp (1) and hose clamp (A). Save hose clamp (1) for reuse and discard hose clamp (A).
Remove two hose clamps (B). Remove and discard the tube, hose, and clamps (B).
Remove bolt (2) and save the part for reuse.
Illustration 2 g03730674
Loosen two hose clamps (3). Remove and discard tube assembly (C).
Illustration 3 g03730675
Install tube assembly (4) from the 466-1958 Heater Kit using two original hose clamps (3) in orientation as shown in Illustration 3.
Illustration 4 g03730676
Install tube (6) using bolt (2) that is saved in Step 3. Install tube (6) to the valve cover hose using original hose clamp (1).
Install hose (7), heater (8), and hose (9) with hose clamp (11) and hose clamp (12). Ensure that heater (8) is positioned as shown in Illustration 3.
Install hose (5) using hose clamp (10).
Illustration 5 g03730677
Disconnect two-pin connector (14) and connect the heater harness.
Route the harness above the Exhaust Gas Recirculation (EGR) coolant hose. Route the harness to the breather hose that runs from the breather canister to the intake.
Install tie straps (15) to secure the connector on the front of the engine, to the EGR coolant hose, and to the breather hose. Refer to Illustration 5.
Connect the harness to the in-line heater.
Bundle and secure any excess harness. Ensure that the harness does not rub other engine components and is not in contact with the exhaust manifold.Machine Software Update
Flash the machine ECM with the 464-6052 Machine Software Gp or later version.Note: The machine software elevates idle speed during cold-weather operation, when the parking brake and the hydraulic lockout are both engaged.Note: If the coolant temperature is less than or equal to 5° C (41° F), then low idle is limited to 1400 rpm. If ambient air temperature is less than or equal to 0° C (32° F) or if coolant temperature is less than or equal to 70° C (158° F) for 7 minutes, then low idle is limited to 2000 rpm.Note: When the machine ECM is flashed, engine diagnostic codes will be created due to the loss of communication between the engine ECM and the machine ECM. These codes will show up as "CAN DATA LINK" codes. After flashing the machine ECM, turn the key switch OFF and back ON (engine not running) and these codes will change from active to logged. With the key switch ON (engine not running) clears the logged codes. If the codes still do not clear, ensure the "All ECM" box is NOT checked.Calibration Procedure for Minimum Fan Speed
The demand fan is a required component to complete this update to decrease the minimum engine fan speed.For the 246D - S/N:BYF, 262D - S/N:DTB, 277D - S/N:FMT, 279D - S/N:GTL, 287D - S/N:HMT, and 289D - S/N:TAW, the demand fan is standard.For the 236D - S/N:BGZ, 242D - S/N:DZT, 257D - S/N:EZW, and 259D - S/N:FTL, the demand fan is an option. For these models if the machine has the standard fan, the demand fan will need to be installed. Refer to 258-2579 Hydraulic Fan Motor and Mounting Gp in SIS web. After installing these components, use the Cat® Electronic Technician (Cat ET) Service Tool to change the configuration for the Demand Fan "Installed".
Calibrate the "Minimum Fan Speed" in the machine ECM.
Illustration 6 g03730679
Foll
Parts clip Suzuki:
13394-12110
13394-12110 Clip, Needle
DT2B, DT2C, DT2N, DT2T, DT2X, DT2Z, DT4.5LB, DT4.5SB, DT4D, DT5LC, DT5LN, DT5SC, DT5SN, DT7.5LB, DT7.5LC, DT7.5LN, DT7.5SB, DT7.5SC, DT7.5SN, DT9C, DT9D, DT9F
09401-08401
09401-08401 Clip, Fuel Hose
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16SB, DT16SC, DT16SN, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ESB, DT25ESC, DT25ESN, DT25MLB, DT25MLC, DT25MLN, DT25
09401-06401
09401-06401 Clip
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16SB, DT16SC, DT16SN, DT7.5LB, DT7.5LC, DT7.5LN, DT7.5SB, DT7.5SC, DT7.5SN, DT9C, DT9D, DT9F
13394-10010
18184-95200
18184-95200 Clip
DT35ELT, DT35ELX, DT35EST, DT35ESX, DT35MLT, DT35MLX, DT35MST, DT35MSX, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC
18195-95200
18195-95200 Clip
30ELE, 30ESE, 30MLE, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25MLJ, DT25
09401-08403
65700-95204
65700-95204 CLIP
DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40