09403-11307 Suzuki Clamp


09403-11307 Clamp Suzuki DT15ELG, DT15ELH, DT15ELJ, DT15ESG, DT15ESH, DT15ESJ, DT15MLG, DT15MLH, DT15MLJ, DT15MSG, DT15MSH, DT15MSJ, DT9.9ELD, DT9.9ELE, DT9.9ELF, DT9.9ELG, DT9.9ELH, DT9.9ESD, DT9.9ESE, DT9.9ESF, DT9.9ESG, DT9.9ESH, DT9.9MLD, DT9.9MLE, DT9.9MLF, DT9.9MLG, DT Clamp
09403-11307 Clamp Suzuki
Rating:
28

Buy Clamp 09403-11307 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Suzuki entire parts catalog list:

DT15ELG 1986
DT15ELH 1987
DT15ELJ 1988
DT15ESG 1986
DT15ESH 1987
DT15ESJ 1988
DT15MLG 1986
DT15MLH 1987
DT15MLJ 1988
DT15MSG 1986
DT15MSH 1987
DT15MSJ 1988
DT9.9ELD 1983
DT9.9ELE 1984
DT9.9ELF 1985
DT9.9ELG 1986
DT9.9ELH 1987
DT9.9ESD 1983
DT9.9ESE 1984
DT9.9ESF 1985
DT9.9ESG 1986
DT9.9ESH 1987
DT9.9MLD 1983
DT9.9MLE 1984
DT9.9MLF 1985
DT9.9MLG 1986
DT9.9MLH 1987
DT9.9MSD 1983
DT9.9MSE 1984
DT9.9MSF 1985
DT9.9MSG 1986
DT9.9MSH 1987

Information:


Illustration 1 g03029438
Schematic for the compression brake circuit
Probable Causes
Codes
Short circuit
Open circuitRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Turn the keyswitch to ON.
C. Access the diagnostic overrides under the "Diagnostics" menu.
D. Start the "Compression Brake Low/High Override".
E. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Low/High Override".
F. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
G. Start the "Compression Brake Med/High Override".
H. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Med/High Override".
I. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
Codes
Result: A 791-5, or 792-5 diagnostic code is active.
Proceed to Test Step 2.
Result: A 791-6, or 792-6 diagnostic code is active.
Proceed to Test Step 4.
2. Create a Short Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" in Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" in Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Fabricate a jumper wire to create a short between the supply wire for the suspect compression brake solenoid and engine ground.
D. Turn the keyswitch to ON.
E. Access the diagnostic overrides under the "Diagnostics" menu.
F. Start the override for the compression brake.
G. Once Cat ET displays the status of the compression brake solenoid, stop the override.
H. Monitor the "Active Diagnostic Code" screen in Cat ET. Record any active diagnostic codes.
I. Turn the keyswitch to OFF. Remove the jumper wire.
Note: A -5 open circuit diagnostic code will be active for the other compression brake solenoid. Ignore the diagnostic codes for the other compression brake solenoid. Ignore any diagnostic codes for the injector solenoids.
Short circuit
Result: A 791-6, or 792-6 diagnostic code is active. The harness wiring is OK.
Proceed to Test Step 3.
Result: A 791-5, or 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness.
If the problem is not resolved, proceed to Test Step 3.
3. Create a Short Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The open could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The short must be created separately at each solenoid.
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Remove the valve cover.
C. Reconnect the valve cover connector.
D. Disconnect the connector on the suspect compression brake solenoid.
E. Inspect the terminals on the connector for the compression brake solenoid for damage.
F. Fabricate a jumper wire to short the two wires for the suspect solenoid on the solenoid connector. Crimp a pin to each end of the jumper wire.
G. Make sure that the solenoid connector securely holds the jumper wire.
Note: Worn terminals and/or damaged terminals on the solenoid connector could cause an intermittent "Open".
H. Turn the keyswitch to ON.
I. Access the diagnostic override under the "Diagnostics" menu.
J. Start the override for the compression brake.
K. Once Cat ET displays the status of the compression brake solenoid, stop the override.
L. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
M. Turn the keyswitch to OFF. Remove the jumper wire.
Short circuit
Result: A 791-6 or a 792-6 diagnostic code is active. The harness wiring between the connector for the compression brake solenoid and the ECM is OK.
Repair: Replace the suspect compression brake solenoid. Verify that the problem is resolved.
Result: A 791-5 or a 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness between the connector for the compression brake solenoid and the valve cover connector.
If the problem is not resolved, proceed to Test Step 4.
4. Create an Open Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Turn the keyswitch to ON.
D. Access the diagnostic override under the "Diagnostics" menu.
E. Start the override for the compression brake.
F. Once Cat ET displays the status of the compression brake solenoid, stop the override.
G. Monitor the Active Diagnostic Code screen on Cat ET. Record any active diagnostic codes.
H. Turn the keyswitch to OFF. Remove the wire short.
I. Reconnect the valve cover connector.
Open circuit detected
Result: A 791-5 or a 792-5 diagnostic code is active. The harness wiring between the valve cover connector and the ECM is OK.
Proceed to Test Step 5.
Result: A 791-6 or a 792-6 diagnostic code is active.
Repair: Repair the harness or replace the harness between the P2 connector and the valve cover connector.
If the problem is not resolved, proceed to Test Step 5.
5. Create an Open Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The short could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The open must be created separately at each solenoid.
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/


Parts clamp Suzuki:

09404-06404
 
09404-06404 Clamp
DT15ELG, DT15ELH, DT15ELJ, DT15ESG, DT15ESH, DT15ESJ, DT15MLG, DT15MLH, DT15MLJ, DT15MSG, DT15MSH, DT15MSJ, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35
36632-95501
 
36632-95501 Clamp, connector grommet
30ELE, 30ESE, 30MLE, DT15 MLE, DT15C, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ELJ, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15ESJ, DT15MLD, DT15MLF, DT15MLG, DT15MLH, DT15MLJ, DT15MSD, DT15MSE, DT15MSF, DT15MSG, DT15MSH, DT15MSJ, DT16L
36622-94300
 
36622-94300 CLAMP
30ELE, 30ESE, 30MLE, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ESD, DT15ESE, DT15ESF, DT15MLD, DT15MLF, DT15MSD, DT15MSE, DT15MSF, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT30ELD, DT30ESD, DT30LF, DT30MLD, DT30MSD, DT30MSE, DT30SF, DT35ELT, DT
33816-96300
 
33816-96300 Clamp, Two Cable
30ELE, 30ESE, 30MLE, DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH, DT15 MLE, DT15C, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ELJ, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15ESJ, DT15MLD, DT15MLF, DT15MLG,
Back to top