33816-96300 Suzuki Clamp, Two Cable

Table 1
J1939 Code and Description CDL Code and Description Comments
3551-31
Engine Oil Priming State N/A The Electronic Control Module (ECM) has detected that the prelubrucation cycle has completed, but the engine has failed to crank. Probable Causes
Engine shutdown switches
Diagnostic codes and event codes
Batteries
Engine starting system
Flywheel ring gear
Driven equipment
Engine accessories
Hydraulic cylinder lock
Internal engine problem
Configuration parameters
DC Power SupplyRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 2
Troubleshooting Test Steps Values Results
1. Check the Engine Shutdown Switches
A. The engine shutdown switches should be in the RUN position. Ensure that the shutdown switches are in the proper positions.
B. When a shutdown occurs, the Electronic Control Module (ECM) must be powered down for at least 15 seconds prior to attempting to start the engine.
Shutdown Switches
Results: The shutdown switches are OK.
Repair: Proceed to the next Step
Results: The shutdown switch is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
2. Check the DC Power Supply
OEM
Refer to OEM Troubleshooting.
3. Check the User-Defined Shutdown Status in Cat ET
A. Connect to Cat ET.
B. Navigate to the Engine Starting status screen.
C. Check the status of User-Defined Shutdown
ON/OFF
Result: User-Defined Shutdown status is off.
Proceed to the next step.
Result: User-Defined Shutdown status is ON. Refer to OEM troubleshooting to determine the reason for the User-Defined Shutdown signal status.
4. Check the Electric Starting System (if applicable)
A. If the application is equipped with an electric starting system, perform the following procedure:
A. Check the wiring to the starting motor solenoid. Refer to the electrical schematic.
B. Check the engine start switch and the engine start relay for electrical power.
C. Check the starting motor cables. If the starting motor cables are corroded, remove the starting motor cables and clean the starting motor cables.
D. Test the operation of the starting motors.
Starter
Results: The electric starter is OK.
Repair: Proceed to Test Step 7
Proceed to Next Step
Results: The electric starter is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
5. Inspect the Flywheel Ring Gear
A. Inspect the flywheel ring gear for damage.
Ring Gear
Results: The flywheel ring gear is OK.
Repair: Proceed to the next Step.
Results: The flywheel ring gear is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
6. Inspect the Driven Equipment
A. Inspect the transmission for damage.
B. Verify that the driveline moves freely.
Driven Equipment
Results: The Driven Equipment is OK.
Repair: Proceed to the next Step.
Results: The Driven Equipment is NOT OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
7. Check the Engine Accessories
A. Remove engine accessories that may prevent the engine cranking and inspect the accessories.
B. The following accessories may prevent the engine cranking:
- Engine oil pump
- High-pressure fuel pump
Engine accessories
Result The engine accessories are OK.
Result: Proceed to the next Step
Result: The engine accessories are not OK.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
8. Check for Hydraulic Cylinder Lock
A. If an injector has been replaced, evacuate any fluids from the cylinder and attempt to start the engine. Fuel will flow from the cylinder head into the cylinders when a unit injector is removed.
B. If the engine will not start, check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors. Check for damaged seals. Determine the type of fluid that locked up the cylinder.
C. If there was a coolant leak, determine the cause of the leak.
D. If there was excessive fuel in the cylinder, replace the seals and reinstall the injector. Drain any excess fuel from the cylinder head.
Hydraulic cylinder lock
Result: The engine does not have a hydraulic cylinder lock.
Repair: Proceed to the next Step.
Result: The engine has a hydraulic cylinder lock.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to the next step.
9. Check for an Internal Engine Problem
A. If a mechanical problem is suspected, disassemble the engine. Refer to the Disassembly and Assembly manual. Inspect the internal components for the following conditions:
- Seizure
- Broken components
- Bent components
Mechanical problem
Result: No mechanical problem
Result: The engine has mechanical problems.
Repair: Repair or replace any worn parts. Refer to the Disassembly and Assembly manual.