09401-06408 Suzuki Clip


09401-06408 Clip Suzuki DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK Clip
09401-06408 Clip Suzuki
Rating:
98

Buy Clip 09401-06408 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Suzuki entire parts catalog list:

DT35CRLH 1987
DT35CRLJ 1988
DT35CRLK 1989
DT35CRSH 1987
DT35CRSJ 1988
DT35CRSK 1989
DT35MCLH 1987
DT35MCLJ 1988
DT35MCLK 1989
DT35MCSH 1987
DT35MCSJ 1988
DT35MCSK 1989
DT35TCLH 1987
DT35TCLJ 1988
DT35TCLK 1989

Information:

1. Remove locknut (3) and the washer. Disconnect lever assembly (2) from the control rod.2. Remove bolts (1), and remove lever assembly (2) from the cylinder head assembly. 3. Remove bolt (5) and clamp (4) that hold the fuel injector in position.
Do not put a force on the fuel injection rack, or cause damage to it when the injectors are removed from the cylinder head assembly.
The inlet fuel line must be removed from the cylinder head assembly before the injectors are removed to prevent fuel leakage into the combustion chambers and the crankcase. Put protective caps on the fuel openings.
If too much fuel leaks into a cylinder, a hydraulic lock will form when the piston moves up during engine start-up. The hydraulic force can be large enough to crack the cylinder head spacer plate.
4. Use a pry bar, and loosen injector (6) from the cylinder head assembly. Pull injector (6) out of the cylinder head assembly, and remove it from the engine. 5. A 6V472 Injector Sleeve is installed on the fuel injectors to prevent contamination from entering the open fuel ports. After cleaning the fuel injector, remove the injector sleeve and O-ring seals (7).6. If necessary, remove the plug from clamp (4) from the cylinder head assembly.Install Fuel Injectors
1. Use tool (A) as shown to make sure the fuel injection rack will move freely by its own weight when injector (6) is turned a total of 180° in both directions. Check the rack movement with the injector spring under compression in several positions.
To prevent a carbon deposit between the injector and the injector bore. Make sure the injector body (especially the tapered area) and the injector bore are clean and free of foreign material.
2. Make sure the three O-ring seals (7) are installed in injector (6), and put 5P960 Multipurpose Grease on the seals and in the bore in the injector.3. Make sure the plug that the anvil of clamp (4) sets on is installed in the top of the cylinder head assembly. Put clean engine oil on the plug and the anvil of clamp (4).
Do not tap or hit on the injector follower to install the injector. Damage and failure of the injector can be the result.
4. Put injector (6) in position in the cylinder head assembly. Install clamp (4), and tighten the bolt and washer to push injector (6) all the way into its bore. Tighten the bolt to a torque of 65 7 N m (48 5 lb ft).5. Check to make sure the fuel injection rack moves freely by hand in the injector after the injector is installed.6. Put lever assembly (2) in position. Connect the lever assembly to control rod (8). Tighten the nut and bolt that fastens the lever assembly to control rod (8) to a torque of 8 2 N m (6 1 lb ft). Make sure lever assembly (2) is engaged correctly with the fuel injection rack. Install the two bolts to hold the lever assembly in place.7. See Testing And Adjusting section for the correct adjustment of the fuel injection control group. Make sure the control group can move to the fuel "OFF" position with the governor linkage disconnected.End By:a. install rocker shaft assemblies and push rods


Parts clip Suzuki:

65781-98500
 
65781-98500 Clip
25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15A, DF15S, DF20A, DF25, DF25(R)S, DF25Q, DF25Q(QR), DF25R, DF25R, DF25T, DF30, DF30Q, DF30Q(QR)
09401-08410
CLIP
09401-08410 CLIP
DF4, DF4, DF46, DF4L, DF6, DF6, DF6L, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXG
15331-94300
 
15331-94300 Clip
DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25MLJ, DT25MSD, DT25MSE, DT25MSF
09401-06405
Clip
09401-06405 Clip
DF40QH, DF40TL, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DT115, DT140, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL,
Back to top