32200-98301 Suzuki Coil Set, Lighting, Battery Charging


32200-98301 Coil Set, Lighting, Battery Charging Suzuki DT3.5LD, DT3.5LE, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5ST, DT3.5SX, DT3.5SZ Coil
32200-98301 Coil Set, Lighting, Battery Charging Suzuki
Rating:
43

Buy Coil Set, Lighting, Battery Charging 32200-98301 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Suzuki entire parts catalog list:

DT3.5LD 1983
DT3.5LE 1984
DT3.5LT 1980
DT3.5LX 1981
DT3.5LZ 1982
DT3.5SD 1983
DT3.5SE 1984
DT3.5ST 1980
DT3.5SX 1981
DT3.5SZ 1982

Information:


Illustration 1 g01390328
Schematic for the CAN data link for the J1 ECM connector
Illustration 2 g01390398
Schematic for the CAN data link for the J2 ECM connector
Illustration 3 g01380568
Connector locations for the CAN data link (rear engine view)
(1) P1 ECM connector
(2) Customer Connector
Illustration 4 g01380580
Connector locations for the CAN data link (top rear engine view)
(2) Customer Connector
(3) Termination resistor
(4) Service tool connector
Illustration 5 g01209797
Terminal locations at the P1 ECM connector that are associated with the CAN data link
(P1-34) CAN data link −
(P1-42) CAN shield
(P1-50) CAN data link +
Illustration 6 g01360095
Terminal locations at the Customer Connector that are associated with the CAN data link
(P1-16) CAN shield
(P1-17) CAN data link +
(P1-18) CAN data link −
Illustration 7 g01209794
Terminal locations at the service tool connector that are associated with the CAN data link
(Terminal C) CAN shield
(Terminal G) CAN data link +
(Terminal F) CAN data link −
Illustration 8 g01355248
Terminal locations at the connector for the termination resistor that are associated with the CAN data link
(Terminal A) CAN data link +
(Terminal B) CAN data link −
(Terminal C) CAN shield
Table 1
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Remove the electrical power from the ECM.
B. Thoroughly inspect connectors (1), (2), and (3). Inspect all of the connectors that are associated with the CAN data link. Refer to Troubleshooting, "Electrical Connectors - Inspect", for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
D. Check the allen head screw on each ECM connector and on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect", for the correct torque values.
E. Check the wiring harnesses for abrasion, for corrosion and for pinch points.
Connectors, Pins, and Sockets
Result: The harness and wiring appear to be OK. Proceed to Test Step 2.
Result: There is a problem in the wiring harness.
Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.
STOP
2. Verify the Proper Installation of the Termination Resistors
A. Remove the electrical power from the ECM.
B. Disconnect the display panel from the data link.
C. Disconnect the Cat® Electronic Technician (ET) from the service tool connector.
D. Disconnect the P1 ECM connector.
Note: Wiggle the harness during the following measurements in order to reveal an intermittent condition.
(E.) Measure the resistance between terminals P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -).
The resistance is between 57 and 63 Ohms.
Result: The resistance is between 57 and 63 Ohms. Proceed to Test Step 3.
Result: The resistance is between 114 Ohms and 126 Ohms. A termination resistor is missing.
Verify that two termination resistors are connected to the data link. One resistor must be located on each end of the data link. The engine is shipped with one termination resistor that is installed between the ECM and the customer connector. Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.
Result: The resistance is less than 57 Ohms. There may be a short circuit in the harness. Proceed to Test Step 3.
Result: The resistance is greater than 126 Ohms. There may be an open circuit in the harness. Proceed to Test Step 4.
Table 2


Parts coil Suzuki:

32200-98821
 
32200-98821 Coil Set, Lighting
DT2B, DT2C, DT2N, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ, DT4.5LB, DT4.5SB, DT4D
33410-98300
 
33410-98300 Coil Assembly, Ignition
DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ
32140-98300
 
32140-98300 Coil, Ignition
DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ
32200-98300
 
32200-98300 Coil Set, Lighting, Battery Charging
DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5ST, DT3.5SX, DT3.5SZ
Back to top