67463-95200 Suzuki Connector, throttle

Table 1
J1939 Code and Description CDL Code and Description Comments
1381-17
Engine Fuel Supply Pump Inlet Pressure : Low - least severe (1) E2172 (1)
Engine Fuel Supply Pump Inlet Pressure : Low - least severe (1) The fuel transfer pump inlet pressure is too low.
1381-18
Engine Fuel Supply Pump Inlet Pressure : Low - moderate severity (2) E2172 (2)
Engine Fuel Supply Pump Inlet Pressure : Low - moderate severity (2) The fuel transfer pump inlet pressure is too low.
5417-0
Fuel Filter (Suction Side) Intake Pressure : High - most severe (3) E1569 (3)
Low Electric Fuel Transfer Pump Outlet Pressure The Clean Fuel Module (CFM) electric lift pump is not working properly.
5417-17
Fuel Filter (Suction Side) Intake Pressure : Low - least severe (1) E1569 (1)
Low Electric Fuel Transfer Pump Outlet Pressure The CFM electric lift pump is not working properly.
5417-18
Fuel Filter (Suction Side) Intake Pressure : Low - moderate severity (2) E1569 (2)
Low Electric Fuel Transfer Pump Outlet Pressure The CFM electric lift pump is not working properly.
Table 2
Associated Codes
J1939 Codes CDL Codes Troubleshooting Procedure
931-5 1627-5 Troubleshooting, "Fuel Priming Pump - Test"
931-6 1627-6 Troubleshooting, "Fuel Priming Pump - Test"
7102-5 4550-5 Troubleshooting, "Fuel Priming Pump - Test"
7102-6 4550-6 Troubleshooting, "Fuel Priming Pump - Test"
1382-16 E1129 Troubleshooting, "Fuel Filter Is Restricted"
Illustration 1 g03743610
(1) Clean Fuel Module (CFM) pump
(2) Fuel transfer pump
(3) High-pressure fuel pump
(4) Tank
Table 3
Component Electrical Checkout
Engine Fuel Supply Pump Actuator Fuel Pump Relay Command Override
Engine Fuel Filter Circulating Pump (CFM) Electric Fuel Transfer Pump Relay Override
Table 4
Troubleshooting Test Steps Values Results
1. Check the Fuel System for Leaks
A. Inspect the fuel system components for restrictions:
- Lines
- Tank
- Transfer pump
B. Refer to Testing and Adjusting, "Fuel System Inspection" for additional information.
Leaks
Result: No leaks were found.
Proceed to Test Step 2.
Result: Leaks were found in the fuel system.
Repair: Repair the leaks.
Verify that the problem is resolved.
2. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Check for an active associated code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: An associated code not is active.
Proceed to Test Step 3.
3. Check for Codes
A. Connect Cat ET.
B. Check for active event codes.
Codes
Result: An E1569, 1381, or 5417 code is active.
Proceed to Test Step 4.
Result: Both an E1569 or 5417 and an E2172 or 1381 are active.
Proceed to Test Step 4.
Result: An E2172 or 1381 is active.
Proceed to Test Step 9.
4. Check for Supply Voltage at the Clean Fuel Module Pump (CFM) Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the wiring harness from the CFM pump.
C. Connect Cat ET.
D. Use Cat ET to perform the following override:
-"Electric Fuel Transfer Pump Relay Override"
E. Measure the voltage between the following pins on the CFM pump connector:
- Pin 2 and Pin 3
- Pin 2 and Pin 4
Voltage
Result: The voltage at the clean fuel pump module connector is equal to system voltage.
Proceed to Test Step 5.
Result: The voltage at the clean fuel pump module connector is not equal to system voltage.
Repair: There is a problem with the power supply circuit between the CFM pump connector and the battery supply. Check the circuit protection device, clean fuel module (CFM) relay, and the ground for the clean fuel module pump circuit. Refer to the appropriate wiring diagram to troubleshoot the circuit.
5. Inspect the Fuel Lines
A. Visually inspect the fuel lines between the fuel tank and the inlet to the clean fuel module. Refer to Systems Operation/Testing and Adjusting, "Fuel System Inspection" for additional information.
B. Inspect the fuel lines for the following:
-Restrictions
-Pinching
-Swelling
C. Check for plugged fuel tank vent lines or a plugged fuel tank suction screen.
Fuel Lines
Result: The fuel lines, tank vent, and suction screen are OK.
Proceed to Test Step 6.
Result: The fuel lines, tank vent, and suction screen are NOT OK.
Repair: Repair or replace the damaged fuel lines.
Verify that the problem has been resolved.
6. Prime the Fuel System
A. Remove the air in the fuel system by performing a priming cycle.
B. Refer to the Operation and Maintenance Manual for additional information.
Priming
Result: The fuel system is primed.
Proceed to Test Step 7.
7. Check the CFM Pump Pressure
A. Turn the keyswitch to the OFF position.
B. Remove the CFM outlet pressure sensor.
C. Connect a fuel pressure gauge to the port where the sensor was removed from the CFM.
D. Turn the keyswitch to the ON position.
E. Connect Cat ET.
F. Use Cat ET to perform the following override:
-"Electric Fuel Transfer Pump Relay Override"
G. Monitor the fuel pressure on the gauge.
30 kpa - 150 kpa (4 PSI - 21.5 PSI)
Result: The CFM pump pressure is within specification.
Proceed to Test Step 8.
Result: The CFM pump pressure is not within specification.
Repair: A failed clean fuel module pump has been detected. Replace the CFM pump.
Proceed to Test Step 12.
8. Check for Proper Operation of the CFM Pump
A. Connect Cat ET.
B. Start the engine.
C. Allow the engine to run for at least 10 minutes.
D. Use Cat ET to monitor the following parameter in the status screen: