11511-87J00 Suzuki COVER, RING GEAR

Recommended Actions
Diagnostic Codes, Event Codes, and ECM Power Supply
Certain diagnostic codes and/or event codes may prevent the engine from starting. Connect the Caterpillar Electronic Technician (ET) and check for active codes and/or logged codes. Troubleshoot any codes that are present before continuing with this procedure.Note: If Cat ET will not communicate with the ECM, the problem is most likely with the electrical power supply to the ECM. Refer to Troubleshooting, "Electrical Power Supply Circuit - Test".Oil Level
Check the engine oil level. If necessary, add oil.Note: Engine oil supplies the injection actuation pressure circuit. Proper engine oil level is necessary for fuel injection.Starting Aids
Air Inlet Heater (If Equipped)
Ensure that the air inlet heater is functioning properly. For additional information, refer to Troubleshooting, "Air Inlet Heater Circuit - Test".Ether Injection System (If Equipped)
Ensure that the ether injection system is programmed to "On". For additional information, refer to Troubleshooting, "Ether Injection System - Test".Oil Grade Plugs
Ensure that the correct oil grade plug is installed. The oil grade plug should match with the oil that is installed in the engine. Do not program the "Engine Oil Weight" with Cat ET.Engine Shutdown Switches (If Equipped)
The engine shutdown switches should be in the OFF position. Use Cat ET to verify the status of the shutdown switches. When a shutdown occurs, the keyswitch must be turned to the OFF position for at least 15 seconds before restarting the engine.Note: If Cat ET will not communicate with the ECM, the problem is most likely with the electrical power supply to the ECM. Refer to Troubleshooting, "Electrical Power Supply Circuit - Test".Engine Speed/Timing
Crank the engine and observe the status for engine speed on Cat ET. If Cat ET indicates 0 rpm, refer to Troubleshooting, "Engine Speed/Timing Sensor Circuit - Test".Note: Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal.
Ensure that the timing reference gear is installed correctly. The engine will not start if the gear was installed backward. Check for proper orientation between the crankshaft and camshaft drive gears. Correct the orientation and/or replace the drive gear, if necessary. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".Injection Actuation Pressure
Ensure that the injection actuation pressure is adequate for the engine to start. Refer to Troubleshooting, "Injection Actuation Pressure - Test".Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for additional information.Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for the correct procedure.
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Check for air in the low pressure fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Testing and Adjusting for more information.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Purge air from the low pressure fuel supply circuit. Refer to Testing and Adjusting, "Fuel System - Prime" for the correct procedure.
Check fuel quality. In temperatures below 0 °C (32 °F), check for solidified fuel (wax). Refer to Special Publication, SEBD0717, "Diesel Fuels And Your Engine".
Check the fuel pressure after the fuel filter while the engine is being cranked. Refer to Testing and Adjusting for the correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve. Refer to Testing and Adjusting for more information.Combustion
Check for combustion problems.