31171-96J00 Suzuki COVER KIT, DUST


31171-96J00 COVER KIT, DUST Suzuki DF15, DF15, DF15, DF150, DF150, DF150, DF15A, DF175, DF175, DF175, DF200, DF200, DF200, DF20A, DF225, DF225, DF225, DF25(R)S, DF250, DF250, DF250, DF250A, DF25R, DF25R, DF300, DF300, DF300A, DF40, DF40, DF40A, DF40A, DF50, DF50, DF50A, DF50A, DF60A, COVER
31171-96J00 COVER KIT, DUST Suzuki
Rating:
8

Buy COVER KIT, DUST 31171-96J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Suzuki entire parts catalog list:

DF15 2004,2005,2006,2007,2008,2009
DF15 2010
DF15 2011
DF150 2006,2007,2008,2009
DF150 2010
DF150 2011
DF15A 2011
DF175 2006,2007,2008,2009
DF175 2010
DF175 2011
DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF20A 2011
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF25(R)S 2006,2007
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011
DF250A 2011
DF25R 2006,2007,2008,2009
DF25R 2010
DF300 2007,2008,2009
DF300 2010
DF300A 2011
DF40 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF40 2010
DF40A 2010
DF40A 2011
DF50 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF50 2010
DF50A 2010
DF50A 2011
DF60A 2010
DF60A 2011
DF70A 2009
DF70A 2010
DF70A 2011
DF80A 2009
DF80A 2010
DF80A 2011
DF8A 2011
DF8AR 2010
DF9.9 2011
DF9.9A 2011
DF9.9AR 2010
DF9.9R 2004,2005,2006,2007,2008,2009
DF9.9TH 2008
DF9.9TH 2009,2010
DF90A 2009
DF90A 2010
DF90A 2011
DF99AR 2010
DF99R 2004,2005,2006,2007,2008,2009
DF99TH 2008,2009,2010

Information:


Illustration 1 g00826376
+5 VOLT SENSOR LOCATIONS
Illustration 2 g00890812
+5 VOLT SUPPLY CIRCUITTest Step 1. Inspect Electrical Connectors And Wiring.
Illustration 3 g00890941
Terminal locations for ECM
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the following connections:
ECM engine harness connector J2/P2
ECM machine harness connector J1/P1
Engine oil temperature sensor J101/P101
Turbocharger outlet pressure sensor J200/P200
Engine oil pressure sensor J201/P201
Atmospheric pressure sensor J203/P203
Injection actuation pressure sensor J204/P204
Fuel pressure sensor J208/P208Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Thoroughly inspect ECM connector J1/P1, ECM connector J2/P2, machine connector J61/P61, and all other connectors in the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Refer to Illustration 3.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasion and pinch points from the sensors back to the ECM.Expected Result:All connectors, pins and sockets should be completely coupled and/or inserted and the harness and wiring should be free of corrosion, abrasion or pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem. Stop.Test Step 2. Connect an Electronic Service Tool and Check for Active Diagnostic Codes.
Connect an electronic service tool to the cab data link connector.
Turn the keyswitch to the ON position while the engine is OFF.
Monitor the active diagnostic code screen of the electronic service tool. Check and record any active diagnostic codes.Note: Wait at least 15 seconds in order for the diagnostic codes to become active.Expected Result:Select the condition of the following codes:
262-03 5 Volt Sensor Supply short to +batt
262-04 5 Volt Sensor Supply short to groundResults:
Active - Proceed to Test Step 3.
Logged ONLY - Proceed to Test Step 5.
Not Active or Logged - The +5 V supply is operating correctly at this time. Stop.Test Step 3. Disconnect The ECM Engine Harness Connector From The ECM.
Connect an electronic service tool to the cab data link connector.
Turn the keyswitch to the OFF position while the engine is off.
Disconnect ECM engine harness connector J2/P2.
Turn the keyswitch to the ON position while the engine is OFF.
Access the active diagnostic code screen on the electronic service tool. Check for one of the following active diagnostic codes:
262-03 5 Volt Sensor Supply short to +batt
262-04 5 Volt Sensor Supply short to groundNote: When ECM engine harness connector J2/P2 is disconnected and the keyswitch is in the ON position, open circuit diagnostic codes will be "Active" or "Logged" for all of the engine sensors. This is normal.Expected Result:The +5 V diagnostic code is active when the ECM engine harness connector is disconnected.Results:
Yes - The +5 V diagnostic code is active when the ECM engine harness connector is disconnected.Repair: Temporarily connect a test ECM to ECM machine harness connector J1/P1. Recheck for a +5 V diagnostic code. If a +5 V diagnostic code is not active, the original ECM is faulty. Reconnect the original ECM and check the +5 V diagnostic codes. If a +5 V diagnostic code becomes active, replace the ECM. Stop.
No - The +5 V sensor diagnostic code is no longer active when the harness is disconnected. Either the harness or a sensor that is attached to the harness is causing the problem. Reconnect the ECM engine harness connector. Proceed to Test Step 4.Test Step 4. Disconnect The +5 V Sensors While Active Diagnostic Codes Are Being Monitored.
Connect an electronic service tool to the cab data link connector.
Turn the keyswitch to the ON position while the engine is OFF.
Access the active diagnostic code screen on the electronic service tool. Verify that one of the following diagnostic codes is active:
262-03 5 Volt Sensor Supply short to +batt
262-04 5 Volt Sensor Supply short to ground
Disconnect the following sensors one at a time:
Engine oil temperature sensor J101/P101
Turbocharger outlet pressure sensor J200/P200
Engine oil pressure sensor J201/P201
Atmospheric pressure sensor J203/P203
Injection actuation pressure sensor J204/P204
Fuel pressure sensor J208/P208
Wait for 30 seconds after each pressure sensor is disconnected while the electronic service tool is being monitored in order to verify that the disconnection of a specific sensor deactivates the +5 V diagnostic code.Note: When the sensors are disconnected and the keyswitch is in the ON position, open circuit diagnostic codes will be active or logged when the +5 V diagnostic codes are no longer active. This is normal. Clear these diagnostic codes after this test step is completed.Expected Result:The original +5 V diagnostic code remains active.Results:
Yes - The +5 V diagnostic code is still active. The harness is the cause of the problem. Leave the sensors disconnected. Proceed to Test Step 5.
No - The +5 V diagnostic code is not active when a specific sensor is disconnected.Repair: Reconnect the sensor that is suspected of causing the problem. If the problem returns after the reconnection of the sensor, disconnect the sensor. If the problem disappears after the disconnection of the sensor, replace the sensor.Clear all diagnostic codes. Verify that the repair eliminates the problem. Stop.Test Step 5. Check the Engine Harness.
Illustration 4 g00890941
Turn the keyswitch to the OFF position while the engine is OFF.
Disconnect ECM connector J2/P2 and ECM J1/P1. Verify that all of the +5 V engine pressure sensors that are attached to the ECM connectors are disconnected.
Engine oil temperature sensor J101/P101
Turbocharger outlet pressure sensor J200/P200
Engine oil pressure sensor J201/P201
Atmospheric pressure sensor J203/P203
Injection actuation pressure sensor J204/P204
Fuel pressure sensor J208/P208
Set a multimeter in order to measure the resistance on the ra


Parts cover Suzuki:

11261-87E10-0EP
 
11261-87E10-0EP COVER, PROTECTION ANODE (BLACK)
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70T
11511-87J00
 
11511-87J00 COVER, RING GEAR
DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL
17615-87J00
 
17615-87J00 COVER, WATER PRESS VALVE
DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL
54221-93E05-0EP
 
54221-93E05-0EP COVER, LOWER MOUNT PORT
DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
12764-94J00
 
12764-94J00 COVER, TIMING BELT
DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
61400-93Y60-0EP
 
61400-93Y60-0EP COVER SET, ENGINE (BLACK)
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z
61400-93Y48-0EP
 
61400-93Y48-0EP COVER SET, ENGINE (BLACK)
DF200, DF200, DF225, DF225, DF250, DF250
15644-93J00
 
15644-93J00 COVER, FUEL FILTER
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
Back to top