36650-95201 Suzuki Cover, joint box


36650-95201 Cover, joint box Suzuki DT50, DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT75TCLD, DT75TCLE, DT75TCLF, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCL Cover

Buy Cover, joint box 36650-95201 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50 1983
DT50ELB 1977
DT50ELC 1978
DT50ELN 1979
DT50ESB 1977
DT50ESC 1978
DT50ESN 1979
DT50M 1980,1981,1982
DT50MLC 1978
DT50MLN 1979
DT50MSC 1978
DT50MSN 1979
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982
DT65ELC 1978
DT65ELN 1979
DT65ESC 1978
DT65ESN 1979
DT75TCLD 1983
DT75TCLE 1984
DT75TCLF 1985
DT85ELT 1980
DT85TCLD 1983
DT85TCLE 1984
DT85TCLF 1985
DT85TCLT 1980
DT85TCLX 1981
DT85TCLZ 1982
DT85TELN 1979
DT85TELT 1980

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A (1)     9U-6198     Crankshaft Turning Tool     1    
A (2)     5P-7306     Housing     1    
5P-7305 Engine Turning Tool     1    
B     136-4632     Engine Timing Pin     1    
C     298-5564     T40 Torx Socket     1    
D     227-4389     E10 Torx Socket     1    
E     370-4657     Rocker Arm Spacer     6    
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02004077
The correct location of valve bridges on valve stems is shown.
Clean valve bridges (6) . Inspect the valve bridges for wear and damage. Replace any valve bridges that are worn or damaged.
Lubricate valve bridges (6) with clean engine oil.
Failure to ensure that ALL valve bridges are correctly seated onto the valve stems will cause interference between the pistons and the valves, resulting in damage to the engine.
Install valve bridges (6) to the valve stems.Note: Install used valve bridges in the original location and in the original orientation. Ensure that the valve bridges are correctly seated on the valves. New valve bridges may be installed in either orientation.
Illustration 2 g02004093
Clean the pushrods. Inspect the pushrods for wear and damage. Replace any pushrods that are worn or damaged.
Apply clean engine oil to both ends of the pushrods. Install the pushrods to the engine with the cup upward.Note: Ensure that the pushrods are installed in the original location and that the ball end of each pushrod is correctly seated in the valve lifters.
Illustration 3 g02085993
If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Position the Valve Mechanism Before Maintenance Procedures" for the correct procedure. Install Tooling (B) through Hole (W) in order to lock the crankshaft.Note: Do not use excessive force to install Tooling (B) . Do not use Tooling (B) to hold the crankshaft during repairs.
Remove Tooling (B) .
Failure to ensure that the crankshaft is positioned at 60 degrees after top dead center will result in interference between the pistons and the valves. Failure to ensure that the crankshaft is positioned at 60 degrees after top dead center will result in damage to the engine.
Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the crankshaft at 60 degrees after top dead center.
Illustration 4 g02003035
Illustration 5 g02307257
Ensure that the rocker shaft assembly is clean and free from wear and damage.
Position the rockershaft assembly with Spotfaces (Y) for Torx screws (7) in the up ward position.
Install Tooling (E) to rocker shaft assembly.
Install Torx screws (7) to the rocker shaft.Note: Ensure that correct Torx screw (7) is installed to Position (X) .


Parts cover Suzuki:

11161-95202-02M
 
11161-95202-02M Cover, cylinder head
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT60CLD, DT60CLE, DT65ELC, DT65ELN, DT65ESC, DT65ESN
36650-95200
 
36650-95200 Cover, joint box
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
61400-95832-01T
61400-95833-01T
61141-95202-01J
 
61141-95202-01J Cover, lower rear
DT50, DT50M, DT50W, DT65, DT65, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
61141-95201-01T
61111-95214-01J
 
61111-95214-01J COVER, LOWER
DT50, DT50M, DT50W, DT65, DT65
61111-95503-01J
 
61111-95503-01J Cover, lower
DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELT
Back to top