54221-93100-01J Suzuki Cover, Lower Bushing Left Hand Side

Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
1076-5 18-5 Engine Fuel Injection Pump Fuel Control Valve : Current Below Normal The Electronic Control Module (ECM) detects the following conditions:
Low current in the output from the ECM to the fuel pump solenoid for 0.6 seconds
There are no active 168 diagnostic codes.
The ECM has been powered for at least 0.25 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code.
This diagnostic code detects a fault in the circuit for the fuel pump solenoid.
1188-5 526-5 Engine Turbocharger 1 Wastegate Drive : Current Below Normal (C7.1 engine only) The ECM detects the following conditions:
A low current condition in the output from the ECM to the solenoid for the wastegate regulator.
There are no active 168 diagnostic codes.
The ECM has been powered for at least 2 seconds.
If equipped, the warning lamp will come on once the diagnostic code has been active for 30 seconds. The diagnostic code will be logged.
The engine will be derated while this diagnostic code is active. After the engine derate has been activated, the electronic service tool will indicate "Turbo Protection Derate Active".
This diagnostic code detects a fault in the wastegate regulator that is most likely to be an open circuit.
1188-6 526-6 Engine Turbocharger 1 Wastegate Drive : Current Above Normal (C7.1 engine only) The ECM detects the following conditions:
A high current condition in the output from the ECM to the solenoid in the wastegate regulator
There are no active 168 diagnostic codes.
The ECM has been powered for at least 2 seconds.
If equipped, the warning lamp will come on once the diagnostic code has been active for 30 seconds. The diagnostic code will be logged.
The engine will be derated while this diagnostic code is active. After the engine derate has been activated, the electronic service tool will indicate "Turbo Protection Derate Active".
This diagnostic code detects a fault in the circuit for the wastegate regulator. This fault is most likely to be caused by a high side short to ground or a low side short to power.
Follow the troubleshooting procedure in order to identify the root cause of the fault. The following background information is related to this procedure:Electronically Controlled WastegateThe C7.1 engine has a turbocharger with an electronically controlled wastegate. Typically, the wastegate is a mechanical valve that is used in the turbocharger in order to regulate the intake manifold pressure to a set value.The control system for the electronically controlled wastegate precisely regulates the intake manifold pressure by using a wastegate regulator to control the wastegate.The required intake manifold pressure is calculated by the software that is contained in the ECM. The ECM uses the wastegate regulator to control the wastegate in order to provide the precise value of intake manifold pressure. The solenoid in the wastegate regulator is controlled by a PWM signal from the ECM.Suction Control Valve for the High-Pressure Fuel PumpThe fuel rail pump solenoid is used to control the output from the fuel rail pump. The solenoid receives an electrical supply from the ECM. The fuel rail pump solenoid is then energized when the fuel is to be pumped into the fuel rail.The amount of fuel that is required is calculated by the software that is contained in the ECM. The fuel pump solenoid is controlled by a PWM signal from the ECM.Due to hardware limits, the A6:E11 Electronic Control Module does not support low side or high side short circuit diagnostic on the High-Pressure Fuel Pump Solenoid.
Illustration 1 g06403979
Schematic for the solenoid valves
Illustration 2 g06404285
Pin locations on the P2 connector for the solenoid valves
(28) Wastegate regulator PWM signal (C7.1 engine only)
(50) Wastegate regulator return (C7.1 engine only)
(72) High pressure fuel pump solenoid return
(94) High pressure fuel pump solenoid PWM signal
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector and the solenoids.
Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the solenoid connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 5 N m (44 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 1076-5 or 1188-5 diagnostic code is active.
Proceed to Test Step 3.
Result: A 1188-6 diagnostic is active.
Proceed to Test Step 5.
3. Create a Short Circuit at the Harness Connector for the Solenoid
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect solenoid.
C. Fabricate a jumper wire that is 150 mm (6 inch) long.
D. Install the wire between the two pins on the harness connector for the suspect solenoid in order to create a short circuit.
E. Turn the keyswitch to the ON position. Wait for 10 seconds. Check for active diagnostic codes on the electronic service tool.
F. Remove the jumper wire from the connector for the solenoid valve.
Diagnostic codes
Result: A -5 diagnostic code was active before installing the jumper. An -6 diagnostic code is active when the jumper is installed - There is a fault in the solenoid.
Repair: