61810-90J01-0EP Suzuki COVER, SIDE STBD (BLACK)


61810-90J01-0EP COVER, SIDE STBD (BLACK) Suzuki DF100, DF100, DF100, DF115, DF115, DF115, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF90 COVER
61810-90J01-0EP COVER, SIDE STBD (BLACK) Suzuki
Rating:
28

Buy COVER, SIDE STBD (BLACK) 61810-90J01-0EP Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Suzuki entire parts catalog list:

DF100 2009
DF100 2010
DF100 2011
DF115 2001,2002,2003,2004,2005,2006,2007,2008,2009
DF115 2010
DF115 2011
DF140 2002,2003,2004,2005,2006,2007
DF140 2008,2009,2010
DF140 2011
DF140T 2002,2003,2004,2005,2006,2007,2008,2009
DF140T 2010
DF140Z 2002,2004,2005,2006,2007,2009
DF140Z 2003
DF140Z 2008
DF140Z 2010
DF90 2001,2002,2003,2004,2005,2006,2007,2008

Information:


Illustration 1 g01141226
Schematic for throttle lock switch
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g01144470
Left side engine view
(1) J1/P1 ECM connectors
Illustration 3 g01144471
Control console next to operator's seat (right side)
(2) Throttle lock switch
Thoroughly inspect ECM connector (1) and the connector for switch (2). Also inspect each of the machine connectors that are in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g01141263
P1 ECM connector
(P1-5) Digital sensor return
(P1-44) Throttle lock control (N/O)
(P1-45) Throttle lock control (N/C)
Illustration 5 g01141445
J705 Throttle lock switch connector
(J705-3) Throttle lock control (N/C)
(J705-4) Digital sensor return
(J705-5) Throttle lock control (N/O)
Perform a 45 N (10 lb) pull test on all of the wires that are in the ECM connectors and on wires (3), (4), and (5) of the connector for the throttle lock switch.
Check the torque of the allen head screw on the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points from the switch back to the ECM. Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be in good repair. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Turn the keyswitch to the ON position.
Check the "Active Diagnostic Codes" screen for a 549-02 diagnostic code. Toggle the throttle lock switch and hold the switch in the active position for several seconds. Check Cat ET for the active diagnostic code.
Turn the keyswitch to the OFF position. Expected Result:A 549-02 diagnostic code is not active.Results:
OK - The switch is operating normally. There may be an intermittent problem.Repair: Check the wiring harness and service equipment for an intermittent electrical problem. Refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - A 549-02 diagnostic code is active. Proceed to Test Step 3.Test Step 3. Check the Resistance of the Switch Circuit at the ECM Connector
Ensure that the keyswitch is in the OFF position.
Disconnect the P1 connector. Note: Wiggle the harnesses during the following measurements in order to detect an intermittent problem.
Measure the resistance between terminals P1-5 (digital sensor return) and P1-44 (throttle lock control (N/O)). The correct resistance measurement is an open circuit.
Measure the resistance between terminals P1-5 (digital sensor return) and P1-45 (throttle lock control (N/C)). The correct resistance measurement is less than five Ohms.
Toggle the throttle lock switch to the ON position. Hold the switch in this position while the measurements are being taken.
Measure the resistance between terminals P1-5 (digital sensor return) and P1-45 (throttle lock control (N/C)). The correct resistance measurement is an open circuit.
Measure the resistance between terminals P1-5 (digital sensor return) and P1-44 (throttle lock control (N/O)). The correct resistance measurement is less than five Ohms.
Connect the J1/P1 connectors. Expected Result:The resistance measurements are within the specifications.Results:
OK - All of the resistance measurements are within the specifications.Repair: Perform the following procedure:
Turn the keyswitch to the ON position.
Use Cat ET to check for the active 549-02 code again. Toggle the throttle lock switch and hold the switch. Check Cat ET for the code. Also, wiggle the switch harness from the switch to the ECM in order to reveal an intermittent problem. If the code does not recur, the problem is resolved. The original problem was probably caused by a poor electrical connection.If the code recurs, the ECM is not detecting the switch inputs correctly. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM".STOP
Not OK - At least one of the resistance measurements is not within specifications. There is a problem in the switch or in a harness. Proceed to Test Step 4.Test Step 4. Check the Operation of the Throttle Lock Switch
Disconnect the J705/P705 throttle lock switch connectors.
On the back of the switch, measure the resistance between terminals J705-1 (throttle lock control (N/C)) and P705-2 (digital sensor return). The correct resistance measurement is less than five Ohms.
Measure the resistance between terminals P705-2 (digital sensor return) and P705-3 (throttle lock control (N/O)). The correct resistance measurement is an open circuit.
Toggle the throttle lock switch to the ON position. Hold the switch in this position while the measurements are being taken.
Measure the resistance between P705-2 (digital sensor return) and P705-3 (throttle lock control (N/C)). The correct resistance measurement is less than five Ohms.
Measure the resistance between P705-1 throttle lock control (N/C) and P705-2 digital sensor return. The correct resistance measurement is an open circuit. Expected Result:The resistance measurements are within the specifications.Results:
OK - The switch is OK. There is a problem in a wiring harness. There may be a problem in a conne


Parts cover Suzuki:

48145-93J00
 
48145-93J00 COVER, TILT LIMIT SWITCH
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, D
63121-87J02
 
63121-87J02 COVER, UNDER
DF100, DF100, DF115, DF115, DF115TL, DF40, DF40, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50QH, DF50TL, DF60, DF60A, DF60HL, DF60TL, DF70, DF70A, DF70A, DF70THL, DF70TL, DF80A, DF80A, DF90, DF90A, DF90A, DF90TL
67263-99E00
 
67263-99E00 COVER, TRIM SWITCH
DF100, DF100, DF115, DF115, DF115TL, DF40, DF40, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50QH, DF50TL, DF60, DF60A, DF60HL, DF60TL, DF70, DF70A, DF70A, DF70THL, DF70TL, DF80A, DF80A, DF90, DF90A, DF90A, DF90TL
63121-87J01
 
63121-87J01 COVER, UNDER
DF100, DF100, DF115, DF115, DF115TL, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DF90, DF90TL
25222-92J00
 
25222-92J00 COVER, SFT GUIDE HSG OIL SEAL
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF90, DF90TL
25222-90J00
 
25222-90J00 COVER, OIL SEAL
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF300, DF300, DF300A, DF90, DF90TL
61400-92800-0EP
 
61400-92800-0EP COVER SET, ENGINE (BLACK)
DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z
61433-92J00
COVER, AIR INTAKE INNER
61433-92J00 COVER, AIR INTAKE INNER
DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z
Back to top