67267-93J00 Suzuki COVER, WIRE

This procedure is for earlier 7000 series fuel injection nozzles with 55.12 mm (2.170 in) adapter bores.Start By:a. remove valve covers FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates.
Do not let the tops of the fuel nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use Tool (A) to loosen fuel injection line (1) at the fuel injection nozzle. 2. Disconnect fuel injection line nut (2) from head adapter nut (3).3. Remove adapter nut (3) and the O-ring seal.4. Move adapter (4) out of valve cover base, and remove fuel injection line (1). 5. If necessary, remove seal (5) from fuel injection line (1). Clamp (6) cannot be removed until fuel injection nozzle (8) is lifted approximately 25.0 mm (1.00 in). 6. Remove bolt (7) that holds clamp (6).7. Remove fuel injection nozzle (8) with Tool (B) as follows: a. Install 6V-6983 Adapter and 6V-4152 Screw (9) part of Tool (B) into fuel injection nozzle (8).b. Install 6V-6982 Tube Assembly (11) over the 6V-4152 Screw. Use 2S-5658 Washer and 1B-2406 Nut (10) on the 6V-4152 Screw to pull fuel injection nozzle (8) from the adapter. Items (10) and (11) are part of Tool (B).
A replacement of compression seal washer (13) and of carbon dam seal (12) must be made each time the fuel injection nozzle is removed. Be sure that the replacement compression seal washer (13) is the same color code and part number as the original compression seal washer. If the wrong thickness washer is used, engine damage could occur. See the Specifications Manual for more detailed information.
8. Remove carbon dam seal (12) and compression seal washer (13) from fuel injection nozzle (8).Install Fuel Injection Nozzles (Earlier 7000 Series)
FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. Earlier fuel injection nozzles are installed in adapters that are below the surface of the cylinder head. 1. Use Tool (A) to clean adapter bore (1) for fuel injection nozzle. Use a tap driver to turn Tool (A). 2. Install compression seal washer (3) on fuel injection nozzle (4).3. Use Tool (A) to install carbon dam seal (2) on fuel injection nozzle (4). Refer to Special Instruction SEHS1292 for the use of Tool (C). 4. Install fuel injection nozzle (4) and clamp (5) as a unit. Install the bolt through the clamp into the adapter. 5. Install O-ring seal on fuel injection line (6), and put clean diesel fuel on it. 6. Install fuel injection line (6). Move adapter (7) into position in the rocker arm cover base.
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
7. Use Tool (B) to tighten the inner fuel line nuts to a torque of 41 7 N m (30 5 lb ft). 8. Put clean diesel fuel oil on O-ring seal (10). Install O-ring seal (10) and nut (9). Tighten nut (9) to a torque of 30 5 N m (22 4 lb ft).9. Install nut (8) for the fuel injection line, and tighten the fuel injection line nut to a torque of 41 7 N m (30 5 lb ft).10. After installation of the valve covers, bleed remove the air from the fuel system. See the Systems Operation, Testing & Adjusting Manual for the correct procedure.End By:a. install valve covers